Recent Posts

Forums | Topics

Page 18 / 41 Prev Next

	Topic Title	Forum
	PETG (Sorry, probably redundant) By shrap 2 weeks ago \| Last Post: 1 week ago	How do I print this? (Printing help)
	I ran some prints overnight in Black PETG using th... 1 week ago By shrap I've never found PETG to be more difficult to prin... 2 weeks ago By hyige... Its not that it comes off bad of the printer. It's... 2 weeks ago By shrap view all posts
	Can't screw nozzles into heaterblock By CyclicElectromagnet 9 months ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I change my heater block in a minute. I don't alwa... 1 week ago By Laban It is not! Before you unroll both cables from the ... 1 week ago By miros... You can buy another heaterblock without nozzle. I ... 2 weeks ago By Laban view all posts
	Print fan rpm test failing (yes, I searched and see all the other posts) By aldumil 1 week ago \| Last Post: 1 week ago	Assembly and first prints troubleshooting
	I found the other threads about this common issue,... 1 week ago By aldum...
	Persistent Warping/Curling on Large Flat Building Models – MK4S – Need Advice By Sebastiaan 1 week ago \| Last Post: 1 week ago	How do I print this? (Printing help)
	Good day everyone, I’m hoping to get some advice f... 1 week ago By Sebas...
	Tool Crash Problem Fixed By KC 2 years ago \| Last Post: 1 week ago	General discussion, announcements and releases
	I made this mod. Docks go nowhere and much nicer m... 1 week ago By joncl You likely need to recalibrate the dock locations.... 1 year ago By Brian I'd recommend pulling the machine out and putting ... 1 year ago By Brian view all posts
	Implementing a filament motion sensor for the Core One By hyiger 3 weeks ago \| Last Post: 1 week ago	User mods
	The prototype is completed and tested over 10 hrs.... 1 week ago By hyige... It can. I'll give a big update later today after a... 2 weeks ago By hyige... Can it detect super slow extrusion mate? like when... 2 weeks ago By gb160 view all posts
	Delete preset printers in 2.9.4 By ChiTownGuy 1 week ago \| Last Post: 1 week ago	PrusaSlicer
	Thank you! 1 week ago By Brian The OP also posted this in the similar thread a f... 1 week ago By Neoph... I have just been able to load and unload the pre I... 1 week ago By brian... view all posts
	5T XL - Bring back the old bed leveling By 1Eye 2 months ago \| Last Post: 1 week ago	Hardware, firmware and software help
	I have the same odd bed leveling with 6.4.0 with p... 1 week ago By schme... Ive experience nozzle cleaning errors for the firs... 3 weeks ago By Chase... I have the same problem... I can't print flexibles... 1 month ago By JC view all posts
	MMU3 By Bobster 1 week ago \| Last Post: 1 week ago	PrusaSlicer
	Suddenly when trying to print a single colour with... 1 week ago By Bobst...
	Débutant - Analyse problèmes d'impression "3D All in one printer test" sur MK3S By Aurélien 1 week ago \| Last Post: 1 week ago	Dépannage pour l'assemblage et les premières impressions
	Bonjour, j'ai acheté une MK3S d'occasion. Elle imp... 1 week ago By Aurél...
	Filament sensor test failure By René 1 week ago \| Last Post: 1 week ago	Assembly and first prints troubleshooting
	OK, found out that i had to push the filament all ... 1 week ago By René Just finished the build of my Core one and running... 1 week ago By René
	First new nozzle By Mchad65 2 weeks ago \| Last Post: 1 week ago	General discussion, announcements and releases
	That is definitely true. The top 4, 220 to 235 wer... 1 week ago By Mchad... After reviewing, break it at each temperature. You... 1 week ago By mnent... I think that's true for almost all quality filamen... 1 week ago By FoxRu... view all posts
	Nostalgia - it's not what it used to be... (One for UK makers) By brianjordan 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	I have just finished my last spool from these peop... 1 week ago By brian...
	Failing print, please help By aerobat 1 week ago \| Last Post: 1 week ago	How do I print this? (Printing help)
	Print 14 - Shafts - print with brim - 0.15mm_PLA_M... 1 week ago By aerob... Didn't see this text "Esun PLA plus" when I made m... 1 week ago By hyige... No idea. Need a lot more information. Please zip y... 1 week ago By hyige...
	Persistent Y-Axis Rattle on MK3S+ By Criptop 2 months ago \| Last Post: 1 week ago	Hardware, firmware and software help
	Hi All, Just following up on this for anyone in ... 1 week ago By Cript... On my MK3, I cannot rotate the bearings when they ... 1 month ago By Robin... Good Luck, Joan 2 months ago By JoanT... view all posts
	Problems with infills on 0.6mm nozzle By Wam 1 week ago \| Last Post: 1 week ago	General discussion, announcements and releases
	HiI have printed long time with 0.4 nozzle with no... 1 week ago By Wam
	PrusaSlicer log in to prusa account By uhrakservit 2 weeks ago \| Last Post: 1 week ago	PrusaSlicer
	Hello! Thanks for reply ... Milan 1 week ago By uhrak... This is a long-standing issue with the Prusa prope... 2 weeks ago By FoxRu... Hello ! In the upper right corner of the applica... 2 weeks ago By uhrak...
	A dumb problem with bed leveling when printing nylon and a solution By TheParrotGuy 3 weeks ago \| Last Post: 1 week ago	General discussion, announcements and releases
	I'm happy that I could help 🙂 Do note that this d... 1 week ago By ThePa... THANK YOU SO MUCH. I just wasted 2-3 hours on noz... 1 week ago By bmont... So I dug some more and found the starting nozzle t... 3 weeks ago By ThePa...
	Dimensional inaccuracy By De Jennes 1 week ago \| Last Post: 1 week ago	Hardware, firmware and software help
	If you review older posts you will find many vari... 1 week ago By Diem When using my MK3s after it being inactive for a w... 1 week ago By De Je...
	Inland filament in Prusa Slicer By LoganWPatch 2 years ago \| Last Post: 1 week ago	PrusaSlicer
	Were you able to update a profile for the Inland '... 1 week ago By kdxra... Has anyone tried these profiles recently? I'm just... 2 months ago By Aspen... It is a great filament if you live near micro cent... 2 years ago By salaz... view all posts