| |
Topic Title |
Forum |
 |
Einbauanleitung Advanced Filtration und GPIO "Hackerboard" set By BastiRun 2 months ago | Last Post: 2 days ago
|
Zusammenbau und Fehlersuche bei den ersten Druckversuchen |
| |
|
 |
Core One - Z osa By Killer85-Z 2 days ago | Last Post: 2 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Test/calibration failures for part fans & hot ends, painful setup finally complete By Fallon 2 years ago | Last Post: 2 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
How to decrease Print Start Time By johnespinoza 1 week ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
 |
NinjaTek Chinchilla TPE (75A) By SLam 2 years ago | Last Post: 2 days ago
|
How do I print this? (Printing help) |
| |
|
 |
Nothing like 24/7 chat support that isn't 24/7 By Barry Robbins 5 months ago | Last Post: 2 days ago
|
General discussion, announcements and releases |
| |
|
|
|
Treat merged objects as separate objects By Eli 2 days ago | Last Post: 2 days ago
|
PrusaSlicer |
| |
|
|
|
Unlocking a little more build volume (with caveats) By darksharpie 6 months ago | Last Post: 2 days ago
|
User mods |
| |
|
 |
Loud noise when unloading, doesn't unload By thealanberman 4 years ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Wifi module not detected By Patrovite 1 week ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Lesitungsaufnahme Standby By JHuesers 1 year ago | Last Post: 2 days ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
| |
|
 |
Nozzle heater check failed By GrimBeaver 2 years ago | Last Post: 2 days ago
|
Assembly and first prints troubleshooting |
| |
|
|
|
Nextruder bzw. Druckkopf wechseln, um Schaden festzustellen By BastiRun 2 weeks ago | Last Post: 2 days ago
|
Hilfe zur Hardware, Firmware und Software |
| |
|
 |
Don't unload filament in single mode? By robertd 2 days ago | Last Post: 2 days ago
|
How do I print this? (Printing help) |
| |
|
 |
Firmware Sources?? By Garvey 3 weeks ago | Last Post: 2 days ago
|
Buddy3D |
| |
|
 |
Nozzle Temperature Sensor - Resistance at Room Temperature By SAVAGENYHK 2 years ago | Last Post: 2 days ago
|
Hardware, firmware and software help |
| |
|
 |
Can't Access PrusaConnect on iMac (PrusaSlicer/Chrome) By Pablob 4 weeks ago | Last Post: 2 days ago
|
Bugs & Errors |
| |
|
 |
Rapid decline in print quality By Flok 4 days ago | Last Post: 3 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Core One: How does the side filament sensor work? (1 viewing) By OA007 6 months ago | Last Post: 3 days ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Awaiting Moderation By pmcgarr 6 years ago | Last Post: 3 days ago
|
General discussion, announcements and releases |
| |
|