Recent Posts

Forums | Topics

Page 19 / 32 Prev Next

	Topic Title	Forum
	Gaps in small emblem By Michael Plumbohm 4 weeks ago \| Last Post: 2 weeks ago	How do I print this? (Printing help)
	You can set a modifier slab so that only the black... 2 weeks ago By Tim First of all, I'd like to thank you all for your r... 4 weeks ago By Micha... The edges of a print will always have some artifac... 4 weeks ago By Tim view all posts
	Disabling "absorb heat" for low bed temp filaments By hyiger 2 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Is this really necessary for TPU, PLA or PETG? I g... 2 weeks ago By hyige...
	Camera stream By BadPixel 2 years ago \| Last Post: 2 weeks ago	General discussion & User Experience & Ideas
	See- someone wrote step by step commands, should b... 2 weeks ago By _Kasz... Mediamtx requires rpi, connected camera, downloade... 2 weeks ago By _Kasz... Hm..this doesn't sound very simple for a less expe... 2 weeks ago By Draku view all posts
	Designers and engineers: Here are the precise dimensions of screw holes and nut pockets By tdk408 4 months ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	I forgot to add, hex nut pockets are 2.4mm deep. I... 2 weeks ago By tdk40... These are the exact M3 screw and nut dimensions fr... 4 months ago By tdk40...
	Buddy Cam Stand Alone Option By Neal 2 months ago \| Last Post: 2 weeks ago	Buddy3D
	me too. It already seems like it's an IP camera, s... 2 weeks ago By Steve... If its not possible already I would like to be abl... 2 months ago By Neal
	Lego ninja turtles for lego Duplo (ABS acetone smoothed) By cyrille.p 8 years ago \| Last Post: 2 weeks ago	Awesome prints (Hall Of Fame)
	I know this thread is a bit old but I have been se... 2 weeks ago By Brian... It's great, you can compete with lego 😀 2 years ago By Leon ... I'm just shocked that decades later, ninja turtles... 2 years ago By Netpa... view all posts
	Delete Team By Pedro P 3 months ago \| Last Post: 2 weeks ago	General discussion & User Experience & Ideas
	I have the exact same problem. Can you have them c... 2 weeks ago By kraql... Happy printing, Pedro! Joan 3 months ago By JoanT... Thanks Joan Looking forward to it 3 months ago By Pedro... view all posts
	Close to losing my mind By J 3 weeks ago \| Last Post: 2 weeks ago	Assembly and first prints troubleshooting
	Umm -- you mean the 230V (or 115V) mains cord? Or ... 2 weeks ago By Jürge... chat lady is sending a new main power cord, as she... 3 weeks ago By J It's likely there is/was a mix up with some of the... 3 weeks ago By Diem view all posts
	Alternative to Octoprint for time lapse videos By Chris 2 weeks ago \| Last Post: 2 weeks ago	User mods - OctoPrint, enclosures, nozzles, ...
	Hi all, and thanks for reading: Does anyone out th... 2 weeks ago By Chris
	Error initializing Prusa Slicer By henriquewf 2 weeks ago \| Last Post: 2 weeks ago	PrusaSlicer
	I keep getting an error initializing Prusa Slicer.... 2 weeks ago By henri...
	TPU on MMU3 By Philip 1 year ago \| Last Post: 2 weeks ago	Hardware, firmware and software help
	To take this one step further - 1) I selected a ... 2 weeks ago By TheNo... I played around quite a bit with different setting... 3 months ago By Enija... Here is a simple procedure: In PrusaSlicer, go to ... 4 months ago By pudni... view all posts
	No chamber temperature in Prusa Link? By Bazim 2 weeks ago \| Last Post: 2 weeks ago	Prusa Connect & PrusaLink
	Hello, am I blind or there is no chamber temperatu... 2 weeks ago By Bazim
	Bambu Labs Lithophane Maker Workflow By JOHNE 1 month ago \| Last Post: 2 weeks ago	General software discussion
	Had a chance to try the Bambu 3mf convertor refere... 2 weeks ago By JOHNE Bambu has a number of nice generator tools in thei... 1 month ago By JOHNE
	Poptávka po tisku - Praha (5) By DanCZer 3 years ago \| Last Post: 2 weeks ago	Nejlepší výtisky & tiskové tipy
	Zdravím funguje tady ještě ta skupina? mohu nabídn... 2 weeks ago By Barví... Poslal jsem email... 3 years ago By DanCZ... Děkuji! Ozvu se! Možná bych to stihl i dnes, ale n... 3 years ago By DanCZ... view all posts
	Prusament PA11 Carbon Fiber Einstellungen By sysoptiger 2 weeks ago \| Last Post: 2 weeks ago	Wie drucke ich das? (Hilfe zum Drucken)
	OK, ich pack das jetzt mal 4 Stunden bei 70° in me... 2 weeks ago By sysop... Das sieht so aus als müsste das Filament getrockne... 2 weeks ago By Walte... So sieht das Ergebnis aus, eine Katastrophe.Brauch... 2 weeks ago By sysop...
	PTFE tube wear? By Arklan 2 weeks ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Thanks, that seems to answer my question. 2 weeks ago By Arkla... Wish we can have a longer period to edit... What I... 2 weeks ago By hyige... It doesn't extends around 1cm into the nextruder a... 2 weeks ago By hyige...
	How does an ol' dummy like me change the support settings? By Essebo 2 weeks ago \| Last Post: 2 weeks ago	PrusaSlicer
	I want to make the supports easier to remove, and ... 2 weeks ago By Esseb...
	Does CORE One print well ABS? By zapta 6 months ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	Since I posted the question here I got a Core One ... 2 weeks ago By zapta Have a friend who has smoked for years. Says he's ... 2 weeks ago By hyige... I've been been printing on a regular basis ASA ( n... 2 weeks ago By Artur... view all posts
	Issues with changing filament and "ejected" hotend By Crysso 3 weeks ago \| Last Post: 2 weeks ago	Assembly and first prints troubleshooting
	It appears from your pictures that for some reason... 2 weeks ago By Steve Hello, After my first two successful prints I wa... 3 weeks ago By Cryss...
	Is the Smart Box a dead project? By IBNobody 2 years ago \| Last Post: 2 weeks ago	General discussion, announcements and releases
	It's not dead, it just smells funny! 🙂 2 weeks ago By Walte... The Smart Box is still listed on the enclosure pro... 3 weeks ago By Tonni is anyone aware if there has been any update thus ... 1 month ago By Alex ... view all posts