Recent Posts

Forums | Topics

Page 9 / 39 Prev Next

	Topic Title	Forum
	Printer printing wrong g code file By GordonMcD 11 months ago \| Last Post: 6 days ago	Hardware, firmware and software help
	I also have this issue. It seems to occur when the... 6 days ago By Johan... Yeah same issue here with my MK3S+ with firmware 3... 2 months ago By Beaco... I als0 have been having this problem...picking th... 2 months ago By Sally... view all posts
	neue Düsen passen nicht ohne Nachbearbeitung By Wolverine0815 1 week ago \| Last Post: 6 days ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Habe ich in dieser Größe noch nie gesehen. 6 days ago By Wolve... Wer Erfahrung hat mit der Mertallbearbeitung, kann... 6 days ago By Frick... Hallo zusammen,ich habe bei meinem MK4 bzw. jetzt ... 1 week ago By Wolve...
	Pin Holes By Bryan Powell 6 days ago \| Last Post: 6 days ago	How do I print this? (Printing help)
	Thank you for your reply Tim. The test part is 3 l... 6 days ago By Bryan... You didn't say how many layers are involved. But i... 6 days ago By Tim Hello, I am attempting to print a lightbox for a b... 6 days ago By Bryan...
	Better anti vibration feet alternative? By perky890 1 week ago \| Last Post: 6 days ago	General discussion, announcements and releases
	I had one of the original Core Ones and it came wi... 6 days ago By vhubb... +1. I used them on all my Core Ones. Work great 6 days ago By FoxRu... You can peel off the adhesive tape and glue them o... 1 week ago By hyige...
	Filament stuck in Bowen tube core one By Hubukai 6 days ago \| Last Post: 6 days ago	Hardware, firmware and software help
	I did try to push down on it, but I still can’t ea... 6 days ago By Hubuk... Remove the Bowden tube from the top of the extrude... 6 days ago By hyige... hey guys, this is the first time I’ve had a little... 6 days ago By Hubuk...
	MMU3 filament load failure By William Westbo 6 days ago \| Last Post: 6 days ago	General discussion, announcements and releases
	I have a MK4 that I upgraded to a MK4S and then I ... 6 days ago By Willi...
	Replacing hot end. 2 wires that I can't figure where they were. By GXS 1 month ago \| Last Post: 6 days ago	Hardware, firmware and software help
	I've never seen wire like that on a Prusa. Perhap... 6 days ago By Tim which version of printer?i know on my mk3 there sh... 6 days ago By Sumta I had a failed ABS print that left the hot end enc... 1 month ago By GXS
	Are there any apps for testing g-code on a Core One By hyiger 6 days ago \| Last Post: 6 days ago	Hardware, firmware and software help
	FWIW, Octoprint on an rpi auto-selects 115200, Coo... 6 days ago By ssmit... Not trying to do anything other than understand wh... 6 days ago By hyige... Simply connect 15200,8,N,1 and sent send. Not sure... 6 days ago By Tim view all posts
	PrusaSlicer 2.9.3 Final is out By Petr Kubiš 1 week ago \| Last Post: 6 days ago	PrusaSlicer
	Tried to delete previous post, but update for fix.... 6 days ago By Danie... Well, this is awkward. Updated to this version and... 6 days ago By Danie... We released the final version of 2.9.3 last week! ... 1 week ago By Petr ...
	PA - Nylon Printing By 6SF5 4 months ago \| Last Post: 6 days ago	How do I print this? (Printing help)
	Fortunately, a spray can of matte clear makes *any... 6 days ago By Erik I guess the only downside (for me) is it's glossy ... 7 days ago By hyige... Nice... comes in 1Kg spools and it much less overa... 7 days ago By GBMar... view all posts
	Unable to control printer with PRUSA App By mmmachnik 6 days ago \| Last Post: 6 days ago	Hardware, firmware and software help
	I recently added a MMU3 to my Core ONE and now the... 6 days ago By mmmac...
	Camera jammed the print board By Justin Craigie 7 days ago \| Last Post: 6 days ago	Hardware, firmware and software help
	Wanted to add here that the Buddy camera magnets s... 6 days ago By hyige... Try a control/calibration/z-alignment? 6 days ago By ssmit... The buddy camera fell during a print and caused th... 7 days ago By Justi...
	MKS4 with mmu3 printed now will not By tweiner 6 days ago \| Last Post: 6 days ago	Assembly and first prints troubleshooting
	I have a MK4S with mmu3. I ordered assembled. Un... 6 days ago By twein...
	Looking for profiles for 3DXTech filaments By Steve 6 days ago \| Last Post: 6 days ago	PrusaSlicer
	Does anyone know where I can find PrusaSlicer prof... 6 days ago By Steve
	MMU Nextruder mod tension screws By Alienbliep 2 weeks ago \| Last Post: 6 days ago	Hardware, firmware and software help
	No scraping at all. I tightened the screws a littl... 6 days ago By James... Does your screws scrape the holes? I suggest tight... 6 days ago By Alien... I have the same problem. Did a few prints without ... 6 days ago By James... view all posts
	Print head strangely shifted right By YigalB 6 days ago \| Last Post: 6 days ago	General discussion, announcements and releases
	While printing this known duck, the head started p... 6 days ago By Yigal...
	Bambu Labs Lithophane Maker Workflow By JOHNE 6 days ago \| Last Post: 6 days ago	General software discussion
	Bambu has a number of nice generator tools in thei... 6 days ago By JOHNE
	What is causing this and how to deal with it. By TheBelcherMan 2 weeks ago \| Last Post: 6 days ago	How do I print this? (Printing help)
	Look at this model I got my inspiration from. Is ... 6 days ago By TheBe... Inside the program, I think the seam is intentiona... 7 days ago By Tim If you pull this little test into the slicer, bone... 7 days ago By TheBe... view all posts
	PrusaConnect keeps showing OFFLINE and other connection issues By Roger 6 months ago \| Last Post: 6 days ago	Bugs & Errors
	I've been having the same issues with my Core One.... 6 days ago By Hammy I'm still getting these Offline statuses, been hap... 2 weeks ago By Chris This has been an intermittent issue with my MK4s. ... 3 weeks ago By gregF view all posts