Recent Posts

Forums | Topics

Page 34 / 34 Prev

	Topic Title	Forum
	Filament spool too wide By iftibashir 4 weeks ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	Maybe find someone locally and offer a spool swap?... 4 weeks ago By _Kasz... I have a new spool of Prusament but it won't fit i... 4 weeks ago By iftib...
	Anyone try Diamondback nozzles? By cwbullet 4 years ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	I don't print with PLA anymore so can't comment on... 4 weeks ago By hyige... I adjusted retraction from .8 to 1.5 I think it wa... 1 month ago By BIGRE... I read somewhere that one small drawback of diamon... 1 month ago By Artur... view all posts
	Buddy camera clicking By Scott 3 months ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	I think I figured this out for mine - it is the ‘m... 4 weeks ago By david... Mine too. Taking pics maybe? Unable to connnect... 1 month ago By Neal +1 on this. One of my CORE One buddy cam's are lig... 2 months ago By Night... view all posts
	Anyone tried USB SD-card reader with high-endurance SD card instead of USB-stick? By ductng 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	I use a micro-SD reader with a SanDisk Ultra 64GB.... 4 weeks ago By hyige... After I read some discussions about USB-stick wear... 4 weeks ago By ductn...
	Failing X and Y Calibration after working for two months. By Raymond 1 month ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	Yes, maintenance was done. I understand about that... 4 weeks ago By Raymo... I presume you have been keeping up with general ma... 1 month ago By Diem A common problem during belt tuning is applying un... 1 month ago By hyige... view all posts
	How did that happen? By Bryan_K 1 month ago \| Last Post: 4 weeks ago	How do I print this? (Printing help)
	So it happened again, this time during a short pri... 4 weeks ago By Bryan... I'm thinking its in the Z axis, but really hard to... 1 month ago By Tim I think there were only a few lines of infill on t... 1 month ago By Bryan... view all posts
	End g-code don't end at requested position By JanP 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	I have also tried to use that standard End g-code ... 4 weeks ago By JanP I use the following End g-code in Pruse Slicer 2.9... 4 weeks ago By JanP
	Prusa Slicer isn't working on my MacBook Pro M1 By Richard3D 4 weeks ago \| Last Post: 4 weeks ago	PrusaSlicer
	Problem solved, threw away the config and then it ... 4 weeks ago By Richa... Prusa Slicer crashes immediately when I start it. ... 4 weeks ago By Richa...
	Filamentende erkennen By Bienemaya 1 month ago \| Last Post: 4 weeks ago	Hilfe zur Hardware, Firmware und Software
	Danke. Das Filament ist gebrochen und er hat nicht... 4 weeks ago By Biene... Also, als erstes mal: Ne neue Düse brauchst da nic... 1 month ago By Digib... Hi zusammen, Ich habe jetzt Trouble gehabt, ... 1 month ago By Biene...
	Download print files from PrusaConnect By mrsam993 1 year ago \| Last Post: 4 weeks ago	Prusa Connect & PrusaLink
	I believe the USB drive is the file storage for th... 4 weeks ago By Green... Same here. I thought files stayed in Connect for a... 11 months ago By Razor Recently the USB for my Prusa Mk4 got corrupted an... 1 year ago By mrsam...
	setting up a BondTech extruder on the mini+ By Dan Borugã 1 month ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	RE: setting up a BondTech extruder on the mini+ 4 weeks ago By _Kasz... I would like to install the Bondtech extruder on m... 1 month ago By Dan B...
	G-Code Fehlerhaft auf USB Stick By Janus Kottisch 1 month ago \| Last Post: 4 weeks ago	Hilfe zur Hardware, Firmware und Software
	Da muss ich mal nachschauen was eingestellt ist. D... 4 weeks ago By Janus... Hast Du die Funktion "Power-loss recovery" (oder s... 1 month ago By Walte... Danke für deine ausführliche Antwort. Formatiert ... 1 month ago By Janus... view all posts