| |
Topic Title |
Forum |
 |
Filamentwechsel ohne Aufheizphase By BastiRun 3 weeks ago | Last Post: 2 weeks ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
| |
|
 |
Partial BRIM possible - not around the entire object? By steve 10 months ago | Last Post: 3 weeks ago
|
PrusaSlicer |
| |
|
 |
PSA / Fixing my bad P.I.N.D.A. 2 probe By eschlenz 8 years ago | Last Post: 3 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Prosa Core One + firmware By MegaPlotz 3 weeks ago | Last Post: 3 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Unable to reload: By 4Thee 4 weeks ago | Last Post: 3 weeks ago
|
PrusaSlicer |
| |
|
 |
Issue setting up new XL during dock calibration. Are my tool changing mechanisms backwards? By bommerts 2 months ago | Last Post: 3 weeks ago
|
Assembly and first prints troubleshooting |
| |
|
 |
XL 6.4.0 dimming no longer functioning By Chase York 4 weeks ago | Last Post: 3 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Prusa Slicer 2.9.3: no "view" and "show" drop down lists in the lower left corner of the Preview Mode after slicing By Alexey Ustinov 3 weeks ago | Last Post: 3 weeks ago
|
PrusaSlicer |
| |
|
 |
PrusaLink Webpage not reachable By JonathanS 2 years ago | Last Post: 3 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Placeholder for Infill? By Jammer 3 weeks ago | Last Post: 3 weeks ago
|
General discussion, announcements and releases |
| |
|
|
|
Corners Lifting on L-shaped Print By Jay 3 weeks ago | Last Post: 3 weeks ago
|
How do I print this? (Printing help) |
| |
|
 |
DIY Alternative for the Advanced Filtration for Prusa CORE One? By jonnieZG 4 weeks ago | Last Post: 3 weeks ago
|
User mods |
| |
|
 |
prusa mini nach 3 Jahren Pause. By Michael Klust 3 weeks ago | Last Post: 3 weeks ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
| |
|
 |
Feature Request -- Add "skip chamber heating wait" By Crystal Lattice 3 weeks ago | Last Post: 3 weeks ago
|
Prusa Connect & PrusaLink |
| |
|
 |
Supports first layer outside print area By Tinus 3 weeks ago | Last Post: 3 weeks ago
|
PrusaSlicer |
| |
|
 |
Selftest failing because of hotend heater/thermistor, which is working fine By qinx 6 months ago | Last Post: 3 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Ringing, or other artefacts on top layer. What could this be? By bvbreukelen 2 months ago | Last Post: 3 weeks ago
|
How do I print this? (Printing help) |
| |
|
 |
BUG MMU2S filament load failure with firmware 3.13.x and 3.14.0 (MMU2S fw 3.0.2) By rcurcu 1 year ago | Last Post: 3 weeks ago
|
Hardware, firmware and software help |
| |
|
 |
Stepper Motor Holding Force By Irma 3 weeks ago | Last Post: 3 weeks ago
|
General discussion, announcements and releases |
| |
|
|
|
Prusa Slicer not showing any System/User presets if another "Printer Preset" is selected By Matteo Passeri 10 months ago | Last Post: 3 weeks ago
|
PrusaSlicer |
| |
|