| |
Titolo discussione |
Forum |
 |
After upgrade from MK3 to MK3S+ can't get good bed contact Da peterpop 3 weeks fa | Ultimi post: 3 weeks fa
|
Assembly and first prints troubleshooting |
| |
|
 |
Printer troubleshooting Da Sonarcreature 2 months fa | Ultimi post: 3 weeks fa
|
General discussion, announcements and releases |
| |
|
 |
Where is the upgraded bed for Core One ? Da Print_Fandango 1 month fa | Ultimi post: 3 weeks fa
|
General discussion, announcements and releases |
| |
|
 |
Possible bug or error in Gcode ? (Layer shift) Da Wuhan 4 weeks fa | Ultimi post: 3 weeks fa
|
General discussion, announcements and releases |
| |
|
 |
Core One - Z osa Da Killer85-Z 3 months fa | Ultimi post: 3 weeks fa
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Core One - tisk více filamenty Da Kukačka 4 months fa | Ultimi post: 3 weeks fa
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Why is this happening i took everything and cleaned and still getting the same thing Da Wince77 3 weeks fa | Ultimi post: 3 weeks fa
|
Hardware, firmware and software help |
| |
|
 |
rattling during printing Da Bezbolestný Pekáč 1 month fa | Ultimi post: 3 weeks fa
|
Prusa CORE One L |
| |
|
 |
prestane dávať filament Da Jamal 3 weeks fa | Ultimi post: 3 weeks fa
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
CORE ONE/ + / L Da Jardoslav 2 months fa | Ultimi post: 3 weeks fa
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
Problém s osou Y Da Skyro 1 month fa | Ultimi post: 3 weeks fa
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
TPU issues, sorry if its been asked before! Da SHeath 3 weeks fa | Ultimi post: 3 weeks fa
|
How do I print this? (Printing help) |
| |
|
 |
First layer resolution different from second layer when should be equal. Da rmayol 3 weeks fa | Ultimi post: 3 weeks fa
|
How do I print this? (Printing help) |
| |
|
|
|
Hot end settings cool down/heat up... Da cboshdave 3 weeks fa | Ultimi post: 3 weeks fa
|
Hardware, firmware and software help |
| |
|
 |
Extruder fördert kein Filament mehr, gibt knackende Geräusche von sich Da Belchengeist 7 months fa | Ultimi post: 3 weeks fa
|
Hilfe zur Hardware, Firmware und Software |
| |
|
|
|
XL 2 tetes, problème 1ere couche Da Erwan QUELLET 3 weeks fa | Ultimi post: 3 weeks fa
|
Dépannage pour l'assemblage et les premières impressions |
| |
|
 |
Change layer direction in Slicer/Gcode - clockwise 1st then next layer counter-clockwise Da Rincewind 3 weeks fa | Ultimi post: 3 weeks fa
|
PrusaSlicer |
| |
|
|
|
The first purge before to print with mmu3 Da rmayol 3 weeks fa | Ultimi post: 3 weeks fa
|
How do I print this? (Printing help) |
| |
|
 |
Accelerometer reduced noise during printing Da docsascha 3 weeks fa | Ultimi post: 3 weeks fa
|
General discussion, announcements and releases |
| |
|
|
|
The Struggles of Warping & Bed Adhesion Da wombatjuggernaut 3 weeks fa | Ultimi post: 3 weeks fa
|
How do I print this? (Printing help) |
| |
|