| |
Titel des Themas |
Forum |
 |
Error #10714 after updating FW to 1.8 Von Rob Meades Vor 6 months | Letzter Beitrag: Vor 4 weeks
|
Hardware, firmware and software help |
| |
|
 |
Prusa MK3S+ vs Bambu Lab X1 carbon Von T_guttata Vor 3 years | Letzter Beitrag: Vor 4 weeks
|
General discussion, announcements and releases |
| |
|
|
|
Layer Shift caused by blob on waste block Von Chneal Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
How do I print this? (Printing help) |
| |
|
 |
Core One with MMU3 issue with Join Sppol Von ddecoste38135 Vor 5 months | Letzter Beitrag: Vor 4 weeks
|
How do I print this? (Printing help) |
| |
|
|
|
Should I Update MK4 to MK4s??? Von Tom De Winter Vor 1 month | Letzter Beitrag: Vor 4 weeks
|
General discussion, announcements and releases |
| |
|
 |
Clicking from extruder and issue with print Von FN_ Vor 2 years | Letzter Beitrag: Vor 4 weeks
|
Assembly and first prints troubleshooting |
| |
|
 |
Duplicate file blocks newer files to printer Von gtomr Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
Prusa Connect & PrusaLink |
| |
|
 |
Nozzle temperature gets stuck at low temperature and not rising midprint Von Arvo-Tec Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
Hardware, firmware and software help |
| |
|
|
|
Silicone bed leveling mod for MK4S Debate Von Dale DiDomenico Vor 1 year | Letzter Beitrag: Vor 4 weeks
|
User mods - OctoPrint, Enclosure, Nozzles, ... |
| |
|
 |
Prusa Slicer can not handle helix ? Von FabLabWag Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
PrusaSlicer |
| |
|
 |
How do I get PrusaSlicer to print the entire outer perimeter first? Von Eug Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
PrusaSlicer |
| |
|
 |
Wiping with Sequential Printing? Von corneliusinspace747 Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
How do I print this? (Printing help) |
| |
|
|
|
PETG fails when other filaments don’t Von BryceP Vor 4 weeks | Letzter Beitrag: Vor 4 weeks
|
How do I print this? (Printing help) |
| |
|
 |
Slowing down the purge Von Peter L Vor 7 years | Letzter Beitrag: Vor 4 weeks
|
General discussion, announcements and releases |
| |
|
 |
Wipe Tower Speed Change Tutorial Von zjohnson16 Vor 3 years | Letzter Beitrag: Vor 4 weeks
|
Hardware, firmware and software help |
| |
|
|
|
Switch off Buddy3D Von Ben Vor 1 year | Letzter Beitrag: Vor 4 weeks
|
General discussion, announcements and releases |
| |
|
 |
"ERR: MINTEMP", not loose wires, possibly the EINSY(?) board? Von bofhdk Vor 3 years | Letzter Beitrag: Vor 4 weeks
|
Hardware, firmware and software help |
| |
|
 |
Print starts when I hit "Set ready" even though I never put anything in the queue Von Scott Gartner Vor 2 years | Letzter Beitrag: Vor 4 weeks
|
Bugs & Errors |
| |
|
 |
Where shall we go? Where would you like to see Prusa at? Von Same Old Shane Vor 4 years | Letzter Beitrag: Vor 4 weeks
|
General discussion, announcements and releases |
| |
|
|
|
Why is it Cheaper to buy from Prusa directly? Von Alan Day Vor 4 months | Letzter Beitrag: Vor 4 weeks
|
General discussion, announcements and releases |
| |
|