| |
Topic Title |
Forum |
 |
First layer calibration looks good, then I get this..... By Jason Watts 4 days ago | Last Post: 12 hours ago
|
General discussion, announcements and releases |
| |
|
|
|
Fliament gets often stuck (or breaks?) when unloading By Teemu Ikonen 1 month ago | Last Post: 12 hours ago
|
How do I print this? (Printing help) |
| |
|
|
|
NOOB: I'm not sure how to describe the problem so please look at these photos. By RayB 6 days ago | Last Post: 13 hours ago
|
How do I print this? (Printing help) |
| |
|
 |
Core One Inconsistent Z-Height across the bed By rwwin 15 hours ago | Last Post: 13 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Simplify3D with a Core 1+ Configuration? By Robert Hill 5 days ago | Last Post: 13 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Proof that Josef Průša is a bad businessman By tdk408 3 weeks ago | Last Post: 14 hours ago
|
General discussion, announcements and releases |
| |
|
 |
The Cryogrip Pro Glacier plate is an excellent cheaper alternative to the Satin plate with one minor caveat on the Core One By hyiger 5 months ago | Last Post: 14 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Mintemp error, but can print after warming up By christopher.a2 14 hours ago | Last Post: 14 hours ago
|
Hardware, firmware and software help |
| |
|
 |
US Tariffs Overturned By solstyce 4 days ago | Last Post: 14 hours ago
|
General discussion, announcements and releases |
| |
|
 |
BUG: How do I remove the old Mini/Mini+ printer profile in PrusaSlicer? By Cassolotl 16 hours ago | Last Post: 15 hours ago
|
PrusaSlicer |
| |
|
 |
Matte black PETG -- any recommendations? By Jürgen 21 hours ago | Last Post: 15 hours ago
|
How do I print this? (Printing help) |
| |
|
|
|
Printer did not stop when it ran out of filament By christopher.a2 22 hours ago | Last Post: 16 hours ago
|
Hardware, firmware and software help |
| |
|
|
|
New found respect for Prusa support By hyiger 2 weeks ago | Last Post: 16 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Buse bouchée By Hades 16 hours ago | Last Post: 16 hours ago
|
Aide concernant le matériel, le firmware ou un logiciel |
| |
|
 |
Thoughts after finishing C1+ assembly and first print By sparebit 2 days ago | Last Post: 16 hours ago
|
Assembly and first prints troubleshooting |
| |
|
 |
2K Filament Storage Solution at HomeDepot By Mac-N4MCC 5 days ago | Last Post: 16 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Current "stance" on several proposed several US states laws in regards to 3D Printing. By Same Old Shane 17 hours ago | Last Post: 17 hours ago
|
General discussion, announcements and releases |
| |
|
 |
How to clean off the nubs from the bed?? By Rob 2 years ago | Last Post: 17 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Is the Smart Box a dead project? By IBNobody 3 years ago | Last Post: 18 hours ago
|
General discussion, announcements and releases |
| |
|
 |
WA State to require DRM blocking, eliminates open-source. makes owners guilty until proven innocent By SouthOfSeattle 3 weeks ago | Last Post: 19 hours ago
|
General discussion, announcements and releases |
| |
|