English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 74 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Skirt distance from object Da David O on Aug 14, 21 5383 21 David O Low density infill and "planes" on top of it Answered Da Florian on Aug 13, 21 3390 6 Florian Precise thickness Da Bryan34 on Aug 12, 21 3313 7 Bryan34 Pushing a polypropylene noodle Da Dan Rogers on Aug 12, 21 1454 2 Zach C Some corners of the layers are lifted (in PETG... Da ssill2 on Aug 11, 21 3738 14 Segad Print quality problem at higher layers Da mereseydotes on Aug 11, 21 3397 8 mereseydotes PETG - "Sandpaper" walls Da Swiss_Cheese on Aug 11, 21 4441 16 Flight777 Single wall printing: Tiny holes/bubbles/zits ... Da Swiss_Cheese on Aug 11, 21 6137 9 maximilliampe... Suppress support through vertical hole Da Frank on Aug 10, 21 3979 14 Frank TPU first layer always has "wrinkles" Da ssill2 on Aug 08, 21 2958 12 Trimetric Sliced layer line not closed Da FoxRun3D on Aug 08, 21 2116 2 tjerkotten Selective Ironing Answered Da Rocky79 on Aug 07, 21 2807 7 Rocky79 Switching between Textured PEI Sheet and Smoot... Answered Da JMHaro on Aug 07, 21 4336 3 JMHaro Why did this part fail? Da Ringarn67 on Aug 06, 21 2685 19 muzz Supported layers are stringy Da cwbullet on Aug 05, 21 13130 43 ssackett Printing multicolor on top of eachother Da ssill2 on Aug 04, 21 16848 16 rocendroll Printing 3 colors (2 same layer) without MMU Da ssill2 on Aug 04, 21 5539 8 mathims Poor quality above support Da ssill2 on Aug 02, 21 1354 3 srbell Strategy for tuning in temperature settings fo... Da Husflid on Aug 02, 21 4728 7 Husflid Any clue why this happened? Da ssill2 on Aug 02, 21 1481 6 Cody Can Pagina 74 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: