English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Avisos Vaciar todo How do I print this? (Printing help) | RSS Página 21 / 187 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Zortrax Filaments Por ezeeone on Jun 14, 23 4073 8 jiblett1000 "Oozing" at top layer(s) Por Hello on Jun 14, 23 1336 2 Constantin Printing ribs to help parts fit Por FoxRun3D on Jun 13, 23 1353 4 epzcaw Advice on printing this item Por Tango on Jun 12, 23 3328 15 Tango Clearance data Por epzcaw on Jun 11, 23 1715 5 epzcaw Can't figure out this error - corners lifting ... Por jsw on Jun 11, 23 3091 13 Chris Print Adhesion issue in lower left corner of b... Por jessestephens1... on Jun 10, 23 1009 1 jessestephens... Printing TPU on Smooth Sheet on MK3S+? Answered Por SGBen on Jun 10, 23 2813 15 3DCoded Vase mode-> 4th layer is squeezed for some odd... Por Robin on Jun 10, 23 1229 3 Roshan Varkey Clapped-Out Mk3 restoration help Por Robin on Jun 09, 23 1099 4 James Sutherl... [Solved] Filament jams each time at same point Por AnneVanLeyden on Jun 09, 23 1579 2 AnneVanLeyden Tall print knocked over Por AnneVanLeyden on Jun 09, 23 2168 6 Siggi Bjarnas... Wall thickness not integer extrusion widths Por JoanTabb on Jun 08, 23 1416 10 DanielNorling Some help with my prints!!? Por Cycleman on Jun 08, 23 1035 1 Cycleman Steel Sheet problems - Do not stick Answered Por jsw on Jun 05, 23 1510 5 Stonefox Slicer settings for LW-PLA RC Aircraft Por DaveE128 on Jun 05, 23 8518 9 Robcarp Prusa Slicer fills in hole in my model - Manif... Answered Por gedeyenite on Jun 01, 23 9686 11 dan007 Inconsistent Nylon Heat Creep Failure Por RyDude575 on Jun 01, 23 1832 4 RyDude575 I am getting continous y-crashes with prusamen... Por Ganymed on May 31, 23 2798 1 Ganymed Under Extrusion at Start of Some Middle Layers Por Lloyd Welder on May 31, 23 2158 2 Lloyd Welder Página 21 / 187 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Siguiente Compartir: