English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Stránka 21 / 187 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Zortrax Filaments Od ezeeone on Jun 14, 23 4073 8 jiblett1000 "Oozing" at top layer(s) Od Hello on Jun 14, 23 1336 2 Constantin Printing ribs to help parts fit Od FoxRun3D on Jun 13, 23 1353 4 epzcaw Advice on printing this item Od Tango on Jun 12, 23 3328 15 Tango Clearance data Od epzcaw on Jun 11, 23 1715 5 epzcaw Can't figure out this error - corners lifting ... Od jsw on Jun 11, 23 3091 13 Chris Print Adhesion issue in lower left corner of b... Od jessestephens1... on Jun 10, 23 1009 1 jessestephens... Printing TPU on Smooth Sheet on MK3S+? Answered Od SGBen on Jun 10, 23 2813 15 3DCoded Vase mode-> 4th layer is squeezed for some odd... Od Robin on Jun 10, 23 1229 3 Roshan Varkey Clapped-Out Mk3 restoration help Od Robin on Jun 09, 23 1099 4 James Sutherl... [Solved] Filament jams each time at same point Od AnneVanLeyden on Jun 09, 23 1579 2 AnneVanLeyden Tall print knocked over Od AnneVanLeyden on Jun 09, 23 2168 6 Siggi Bjarnas... Wall thickness not integer extrusion widths Od JoanTabb on Jun 08, 23 1416 10 DanielNorling Some help with my prints!!? Od Cycleman on Jun 08, 23 1035 1 Cycleman Steel Sheet problems - Do not stick Answered Od jsw on Jun 05, 23 1510 5 Stonefox Slicer settings for LW-PLA RC Aircraft Od DaveE128 on Jun 05, 23 8518 9 Robcarp Prusa Slicer fills in hole in my model - Manif... Answered Od gedeyenite on Jun 01, 23 9686 11 dan007 Inconsistent Nylon Heat Creep Failure Od RyDude575 on Jun 01, 23 1832 4 RyDude575 I am getting continous y-crashes with prusamen... Od Ganymed on May 31, 23 2798 1 Ganymed Under Extrusion at Start of Some Middle Layers Od Lloyd Welder on May 31, 23 2158 2 Lloyd Welder Stránka 21 / 187 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Další Share: