English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 173 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author GRID Infill and Nozzle Wear Przez -- on Nov 12, 18 3222 3 -- Object not sticking to raft Przez Peel on Nov 11, 18 8572 9 Peel Curved Edges & Corners? Przez toaf on Nov 10, 18 7172 12 Wingsy Lopsided Print Przez Mustrum Ridcul... on Nov 09, 18 2492 4 Wingsy Sainsmart TPU and issues printing bridges/over... Przez Malibusteve on Nov 09, 18 3484 2 malibusteve diagonal lines and blisters in the pieces Przez Abelquiles.com on Nov 08, 18 6440 4 Abelquiles.co... Multicolor print (1 extruder) => please hel... Przez kevin.r5 on Nov 08, 18 1985 6 Valiran First Layer not uniform Przez turfsk8r on Nov 07, 18 3290 4 Andrew Printing a chain or helix on MK3 with PLA Przez toaf on Nov 07, 18 1930 2 Hofnagel Extruding "late start" Przez Williwaw on Nov 06, 18 1518 1 Williwaw Support fails halfway + nozzle scraping Przez michael.c84 on Nov 06, 18 2022 1 michael.c84 Printing parameters to change to print to desi... Przez emil.g on Nov 05, 18 1735 3 emil.g Rough Printing on overhangs on half of model o... Przez Jon on Nov 05, 18 1888 3 Jon Distorting, lifting off the bed Przez trilbytim on Nov 04, 18 1638 4 trilbytim Layers after the first layer are incomplete Przez RetireeJay on Nov 03, 18 2470 4 bastian.s2 Ghost comes unstuck from the bed during printi... Przez toaf on Nov 03, 18 7577 31 Breazile PEI Board PLA no longer sticking Przez toaf on Nov 03, 18 3315 8 Rick 1st Time PETG Printing Przez Eric Lee on Nov 03, 18 2708 6 ian.m32 selective removal of supports ONLY at bed? Przez Tom on Nov 03, 18 4234 10 Tom Printing with a filament smaller than 1.5mm Przez remco.s on Nov 02, 18 3643 5 remco.s Strona 173 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: