English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 173 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Distorting, lifting off the bed Da trilbytim on Nov 04, 18 1433 4 trilbytim Layers after the first layer are incomplete Da RetireeJay on Nov 03, 18 2228 4 bastian.s2 Ghost comes unstuck from the bed during printi... Da toaf on Nov 03, 18 6788 31 Breazile PEI Board PLA no longer sticking Da toaf on Nov 03, 18 2821 8 Rick 1st Time PETG Printing Da Eric Lee on Nov 03, 18 2432 6 ian.m32 selective removal of supports ONLY at bed? Da Tom on Nov 03, 18 3822 10 Tom Printing with a filament smaller than 1.5mm Da remco.s on Nov 02, 18 3352 5 remco.s Printing Aluminum abrasive filament, replace h... Da remco.s on Nov 02, 18 2538 6 remco.s Asa filament with MK3, is it worth for try? Da arto.h on Nov 02, 18 1600 1 arto.h Two process printing - on second process layer... Da toaf on Nov 01, 18 2027 7 Brooks First top infill layer problem Da NM on Nov 01, 18 5623 6 NM impossible to print anymore !! and stick on th... Da Cédric.M on Oct 31, 18 4176 15 Patrick.b First layer waves appearing Da toaf on Oct 31, 18 2477 3 W3D Figure impossible to print! Da Nessuno0505 on Oct 30, 18 2295 4 Nessuno0505 Printing pipe clamp Da gary.b on Oct 29, 18 2537 3 Shesby Scaling problem between Fusion 360 and Slic3r Da AndyT on Oct 27, 18 3268 3 AndyT Hatchbox Wood Problems Da termlimit on Oct 27, 18 3276 5 adam.f17 TPU Feeding Problems Da JoanTabb on Oct 27, 18 1942 2 Keith NOOB, this is fun! (really!) heat bed question... Da OZz on Oct 27, 18 1526 3 OZz Printing PETG is just sucking Da jon.s13 on Oct 26, 18 7495 12 jon.s13 Pagina 173 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: