English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Page 173 / 190 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Suivant Titre du sujet Dernier message Nombre de vues Messages Author Printing a chain or helix on MK3 with PLA Par toaf on Nov 07, 18 1834 2 Hofnagel Extruding "late start" Par Williwaw on Nov 06, 18 1370 1 Williwaw Support fails halfway + nozzle scraping Par michael.c84 on Nov 06, 18 1864 1 michael.c84 Printing parameters to change to print to desi... Par emil.g on Nov 05, 18 1616 3 emil.g Rough Printing on overhangs on half of model o... Par Jon on Nov 05, 18 1709 3 Jon Distorting, lifting off the bed Par trilbytim on Nov 04, 18 1524 4 trilbytim Layers after the first layer are incomplete Par RetireeJay on Nov 03, 18 2312 4 bastian.s2 Ghost comes unstuck from the bed during printi... Par toaf on Nov 03, 18 7052 31 Breazile PEI Board PLA no longer sticking Par toaf on Nov 03, 18 3036 8 Rick 1st Time PETG Printing Par Eric Lee on Nov 03, 18 2512 6 ian.m32 selective removal of supports ONLY at bed? Par Tom on Nov 03, 18 3974 10 Tom Printing with a filament smaller than 1.5mm Par remco.s on Nov 02, 18 3449 5 remco.s Printing Aluminum abrasive filament, replace h... Par remco.s on Nov 02, 18 2640 6 remco.s Asa filament with MK3, is it worth for try? Par arto.h on Nov 02, 18 1653 1 arto.h Two process printing - on second process layer... Par toaf on Nov 01, 18 2100 7 Brooks First top infill layer problem Par NM on Nov 01, 18 5773 6 NM impossible to print anymore !! and stick on th... Par Cédric.M on Oct 31, 18 4341 15 Patrick.b First layer waves appearing Par toaf on Oct 31, 18 2561 3 W3D Figure impossible to print! Par Nessuno0505 on Oct 30, 18 2362 4 Nessuno0505 Printing pipe clamp Par gary.b on Oct 29, 18 2673 3 Shesby Page 173 / 190 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Suivant Partager :