English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Benachrichtigungen Alles löschen How do I print this? (Printing help) | RSS Seite 173 / 190 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Printing a chain or helix on MK3 with PLA Von toaf on Nov 07, 18 1832 2 Hofnagel Extruding "late start" Von Williwaw on Nov 06, 18 1367 1 Williwaw Support fails halfway + nozzle scraping Von michael.c84 on Nov 06, 18 1862 1 michael.c84 Printing parameters to change to print to desi... Von emil.g on Nov 05, 18 1616 3 emil.g Rough Printing on overhangs on half of model o... Von Jon on Nov 05, 18 1708 3 Jon Distorting, lifting off the bed Von trilbytim on Nov 04, 18 1523 4 trilbytim Layers after the first layer are incomplete Von RetireeJay on Nov 03, 18 2310 4 bastian.s2 Ghost comes unstuck from the bed during printi... Von toaf on Nov 03, 18 7026 31 Breazile PEI Board PLA no longer sticking Von toaf on Nov 03, 18 3031 8 Rick 1st Time PETG Printing Von Eric Lee on Nov 03, 18 2510 6 ian.m32 selective removal of supports ONLY at bed? Von Tom on Nov 03, 18 3968 10 Tom Printing with a filament smaller than 1.5mm Von remco.s on Nov 02, 18 3447 5 remco.s Printing Aluminum abrasive filament, replace h... Von remco.s on Nov 02, 18 2627 6 remco.s Asa filament with MK3, is it worth for try? Von arto.h on Nov 02, 18 1652 1 arto.h Two process printing - on second process layer... Von toaf on Nov 01, 18 2097 7 Brooks First top infill layer problem Von NM on Nov 01, 18 5770 6 NM impossible to print anymore !! and stick on th... Von Cédric.M on Oct 31, 18 4333 15 Patrick.b First layer waves appearing Von toaf on Oct 31, 18 2559 3 W3D Figure impossible to print! Von Nessuno0505 on Oct 30, 18 2361 4 Nessuno0505 Printing pipe clamp Von gary.b on Oct 29, 18 2671 3 Shesby Seite 173 / 190 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Nächstes Teilen: