English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Benachrichtigungen Alles löschen How do I print this? (Printing help) | RSS Seite 162 / 190 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Interesting discovery re filament thickness to... Von Mustrum Ridcul... on Feb 28, 19 6225 8 Haku3D Hatchbox Wood PLA Von BitBytePixelSp... on Feb 28, 19 3351 3 BitBytePixelS... Perimeters Not Crossing at Start and End Poin... Von JBinFL on Feb 28, 19 2190 2 tim.o14 Layer separation between 1st & 2nd with PE... Von K-Lab on Feb 27, 19 6616 5 tj Tricky geometry/PETG overhang - Advice needed. Von Bunny Science on Feb 27, 19 18372 24 vintagepc How do I print with ABS? Von wieman01 on Feb 26, 19 2872 9 Andreas Temperature droping... Von JBinFL on Feb 26, 19 1001 9 Vasquez21 Bad layer adhesion Von -- on Feb 25, 19 2943 2 justin.h25 Printing Prusa ABS please help Von jonboy1969 on Feb 23, 19 4787 7 Plugs White prusament = disappointment and problems Von flioink on Feb 23, 19 3609 7 flioink Inner perimeter prints before "infill&quo... Von timo.m on Feb 22, 19 6532 4 DaJMasta strange artifacts on one layer tick print Von frx08 on Feb 21, 19 1243 1 frx08 Can't figure how to get my top layers to print... Von Nikolai on Feb 21, 19 1049 8 Jaxel Prints below freezing Von Andrew Chaee on Feb 21, 19 9375 5 JMcK Problem with Flexiable Filament Von Nikolai on Feb 20, 19 1769 2 ben.w17 Weather station radiation shield Von Dimitar Mitev on Feb 20, 19 8707 27 Dimitar Mitev Help with new R4 Upgrade Parts (PETG) Von jules.c on Feb 20, 19 2297 2 Rodrigo Marin Print your MK3S Upgrade Kit Part Von jules.c on Feb 20, 19 1946 2 jules.c Acetone treatment does not smooth Prusa's ABS Von Vojtěch on Feb 19, 19 5562 6 Elephantik PRUSA MK3 Heated Bed Temperature Differential Von -- on Feb 19, 19 2352 2 kenr Seite 162 / 190 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Nächstes Teilen: