English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 153 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author Changing Initials Przez Peter M on May 30, 19 1888 3 weeble Polcarbonate "burnt knots" Przez bobstro on May 30, 19 2876 13 Rob Meades Flexfill 98a fine tuning problems Przez Abdul on May 28, 19 2332 4 Abdul A horizontal flat rectangular tube Przez Vojtěch on May 28, 19 2958 5 John Help Printing the Elder Wand_with Core_Edited ... Przez Frank_The_Rock on May 28, 19 2544 7 Frank_The_Roc... Printing miniature figures for table top games Przez Nightfox7 on May 27, 19 31062 25 Dingus Printer stops every x time and ask for filamen... Przez JBinFL on May 25, 19 2018 6 diedhert Prints will not stick to the steel bed Przez miles-h2 on May 25, 19 1826 9 miles-h2 Onewheel XR Floats Przez John Doe on May 25, 19 1479 4 John Doe MMU2S help Przez gnat on May 25, 19 1524 3 Pablo Lereu PETG 'Candyfloss' or 'Cotton Candy' Przez Frostie on May 24, 19 1600 1 Frostie SDL into GCODE Przez JMcK on May 24, 19 1801 2 FishHatter SDL into GCODE Przez FishHatter on May 24, 19 1621 1 FishHatter Printing with colorfabb copperfill Przez tsamisa on May 23, 19 3632 12 tsamisa 0.25mm nozzle for miniatures.. just a lot of n... Przez bobstro on May 23, 19 2335 2 charwoodeng SainSmart TPU Setting Przez 24879845 on May 23, 19 1994 1 24879845 Quantum 3D ABS Przez JMcK on May 23, 19 1490 1 JMcK Supports Issue Przez Jim B on May 22, 19 1351 1 Jim B Shall I replace the nozzle? Przez jsada.xyz on May 22, 19 2065 3 jsada.xyz Top layer too wide Przez dustin.l4 on May 22, 19 2151 1 dustin.l4 Strona 153 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: