English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 148 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author Can not get PETG to print Przez bobstro on Jul 31, 19 6917 11 SEMusical Printing with CPE, heavy warping Przez Kovir Wyttclif... on Jul 31, 19 2065 1 Kovir Wyttcli... How would you orient this to print this? Got t... Przez -- on Jul 31, 19 2221 6 eikido Bounding Box Przez Dave Avery on Jul 29, 19 2351 5 michael_phill... PLA prints do not finish Przez Sembazuru on Jul 26, 19 2841 6 BrentV Nylon Gear Bearings Przez Lvet on Jul 26, 19 5474 12 Lvet FlexFill 98 print takes 3 times longer? Przez Frank on Jul 26, 19 1985 4 Frank Clear filament options Przez vintagepc on Jul 25, 19 9774 14 laurel.w Printing small parts with small tolerances Przez schroeder-s on Jul 25, 19 6744 7 schroeder-s Spine Print from Thingiverse Przez RAH1 on Jul 25, 19 2791 11 hhughes Extruder problem Przez -- on Jul 24, 19 1854 3 gsorbara can't fix PLA stringing Przez JoanTabb on Jul 24, 19 10580 8 teus Powdered Sheet .. PLA .. Marvin goes for a wal... Przez bobstro on Jul 24, 19 9376 42 Sink PETG first layer advice Przez Peter M on Jul 24, 19 5501 5 Burger_01 PETG Printing problems Przez Juan Lasso on Jul 23, 19 4862 14 Juan Lasso Rough Top Surface When Printing with Wood Fila... Przez ajlenze on Jul 23, 19 6761 16 ajlenze Pre-heat temp selection when changing filament... Przez -- on Jul 22, 19 1507 2 bob Prints suddenly turned hideous... Przez Bunny Science on Jul 22, 19 2417 7 moonglum Is this heat creep? Przez -- on Jul 22, 19 6364 4 sin Stringy. Is it possible to print this without ... Przez eikido on Jul 22, 19 1497 1 eikido Strona 148 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: