English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 101 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Square-Support not printed clean Da floh on Dec 05, 20 1792 3 floh PETG Benchy issues Da Ritzy on Dec 05, 20 6927 5 Ritzy Printer prints mid air after while Da Lize on Dec 04, 20 5610 7 Mads Nielsen Can't print Troll Hair Answered Da Swiss_Cheese on Dec 04, 20 2374 4 happyday.mjoh... Is it possible to print 0.07mm accurately with... Answered Da FoxRun3D on Dec 04, 20 5479 4 Gabokirby Pretty PLA v4 pofile Da Dan Rogers on Dec 04, 20 2268 3 Lvet two materials one extruder? Da Swiss_Cheese on Dec 02, 20 2870 9 rote-locke Moon Lithophane - Failed Top Da MiLkiE on Dec 02, 20 2479 1 MiLkiE Proper Orientation? Answered Da Slumb3rjack on Dec 02, 20 3558 5 Slumb3rjack First layer issue: circles not closing complet... Da Swiss_Cheese on Dec 02, 20 10761 25 nazarethekmek... Fine detail printing Da Swiss_Cheese on Dec 02, 20 2904 5 mbuto PETG Printing Da Area51 on Dec 01, 20 2425 5 Scouter456 taulman t-glase, inconsistent transparency Da khlae on Dec 01, 20 2068 1 khlae Rough/scarred perimeters Da rgok on Nov 30, 20 1378 1 rgok Issue when printing FLEX Da Swiss_Cheese on Nov 30, 20 7657 17 benedikt.n2 Poor PLA adesion on Powder Coated PEI Da Peter M on Nov 29, 20 2390 3 NathanK Which filament to use for strength? Da Swiss_Cheese on Nov 29, 20 11358 13 Roger Print a test line. Answered Da Szumi on Nov 28, 20 7061 12 Harry Debris fall on the bed, stringing after changi... Da Alk on Nov 28, 20 2342 2 Alk Slicer artifact on flat layer Da Swiss_Cheese on Nov 28, 20 2647 13 joh Pagina 101 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: