RE: Max temp error, then blank screen, now printer stops while printing.
ok turn printer off conect evrything up then do a first layer cal at any point if you here a pop or any strange noise turn printer off asap
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
going to give that a whirl. hang tight.
RE: Max temp error, then blank screen, now printer stops while printing.
let me know when evrything is conected
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
fingers crossed
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
So first time I went to turn it on it was stuck on the loading screen, however I just pulled a few things out and put them back I likely didn't have the filament sensor in correctly but it's booting up right now. I just am going to unload the filament that I had sitting in the extruder.
RE: Max temp error, then blank screen, now printer stops while printing.
ok if it got stuck on loading screen turn printer on and of a couple of times and see if it does it again
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
I managed to unload and load filament no problem, I have a short print i'm going to try. I appreciate all the help today. I'm thinking it could have been a lose connection that was causing the machine to disconnect. It's looking like the first layer is going well, no issues that I can see with temp and the screws holding in the wires for the power are all clean contacts and tightened in.
RE: Max temp error, then blank screen, now printer stops while printing.
ok let me know how print goes if it gets stuck on loading screen again or somthing else happens it has to be the psu
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
Well thank you again for all the help I'll give this thread a reply if anything pops up. You're my new favorite internet stranger. But all jokes aside, I really apprecaite you walking me through all this. It's greatly apprecaited. 🙂
RE: Max temp error, then blank screen, now printer stops while printing.
all good happy to help you
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
hows it going
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
So far so good. it's made it past the point of shut off from the last print. I can't see anything that's looking off at all. No weird sounds, temps staying even, it actually sounds better than the last good print I had a couple weeks ago.
RE: Max temp error, then blank screen, now printer stops while printing.
thats good that its working know
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
Just thought Id check in did the print work
Please help me out by downloading a model it's free and easy but really helps me out https://www.printables.com/@Hello_474427/models
RE: Max temp error, then blank screen, now printer stops while printing.
It did! It turned out great. I'm halfway through a second print now and no issues along the way. Just smooth sailing. Thanks again!