Notifications
Clear all

Just upgrade to MMU 2.0 and Self Test X Axis Fails  

  RSS
Brien
(@brien)
Eminent Member
Just upgrade to MMU 2.0 and Self Test X Axis Fails

The X Axis moves the full length and then tells me there is an error on the X axis.

Belts are Tight and it looks like it moves the entire width of the printer.

Upgraded to Firmware 3.4 as well for the MMU.

Publié : 02/10/2018 3:16 am
Brien
(@brien)
Eminent Member
Topic starter answered:
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails

Well, I shut it off, ate dinner, came back and now it's decided to cooperate....

It now passes calibration.

Publié : 02/10/2018 6:08 am
toaf
 toaf
(@toaf)
Noble Member
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails

guess it was hungry. 😀

I have a Prusa,therefore I research.

Publié : 02/10/2018 9:06 am
CybrSage
(@cybrsage)
Honorable Member
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails


Well, I shut it off, ate dinner, came back and now it's decided to cooperate....

It now passes calibration.

You showed it who is the boss. It was an alpha battle and you won. It will cooperate now, though expect it to test you now and again for leadership.

The key to 3D Printers is that you can NEVER show it weakness. Always let it know you are in charge else it could turn a great experience into a nightmare. 🙂

Publié : 02/10/2018 10:04 pm
Mustrum Ridcully
(@mustrum-ridcully-2)
Honorable Member
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails



Well, I shut it off, ate dinner, came back and now it's decided to cooperate....

It now passes calibration.

You showed it who is the boss. It was an alpha battle and you won. It will cooperate now, though expect it to test you now and again for leadership.

The key to 3D Printers is that you can NEVER show it weakness. Always let it know you are in charge else it could turn a great experience into a nightmare. 🙂

Approaching the printer with a large wrench or hammer in hand and a grim expression can establish proper attitude but be sure to reward good performance once in a while 😀 :geek:

Publié : 02/10/2018 10:54 pm
Neal
 Neal
(@neal)
Reputable Member
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails

Oh yes establish dominance. Show it who is in charge. While checking on it every so often, giving it as close to a climate controlled environment as possible, feeding it only the best filaments, endless hours tweaking and showering love and attention on it.

Trust me. The freaking printer KNOWS who is in charge!

Just sayin',

Neal

Publié : 02/10/2018 11:34 pm
Olef
 Olef
(@olef)
Prominent Member
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails


Oh yes establish dominance. Show it who is in charge. While checking on it every so often, giving it as close to a climate controlled environment as possible, feeding it only the best filaments, endless hours tweaking and showering love and attention on it.

Trust me. The freaking printer KNOWS who is in charge!

Just sayin',

Neal

:mrgreen: :mrgreen: :mrgreen:

Publié : 03/10/2018 7:58 am
toaf
 toaf
(@toaf)
Noble Member
Re: Just upgrade to MMU 2.0 and Self Test X Axis Fails

every time you print....be the sandwich.... I need to print that

I have a Prusa,therefore I research.

Publié : 03/10/2018 8:27 am
Partager :