Notifications
Clear all

Stringing and Holes - HELP 🙁  

  RSS
LindsKay
(@lindskay)
Active Member
Stringing and Holes - HELP 🙁

Hello everyone, I've tried so many things to try to fix my printer and calibrate it, but nothing seems to work. Here are my best so far settings of the printing, and a picture of the calibration pillars I've been using. I very recently perfected the first layer calibration and clean the extruder to the nines. I use good quality PLA from filamentum. Any suggestions will be tried!

Napsal : 18/08/2022 8:47 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Stringing and Holes - HELP 🙁

...before using a new filament for the first time, I would recommend printing a temptower with the Prusa presets. This allows you to adjust temperatures and fan settings and optimize them if necessary.

https://www.printables.com/de/model/4667-all-in-one-temperature-bridging-tower-pla-petg-gco

wbr,

Karl

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Napsal : 18/08/2022 9:13 pm
Diem
 Diem
(@diem)
Illustrious Member

Is this a new printer?

You appear to have three issues together -

 

First, reset to defaults.

Next dry your filament. 

Then print a first layer calibration pattern and show us the result *on the print sheet*

After that we may look at belt tensions...

Cheerio,

 

Napsal : 18/08/2022 10:56 pm
LindsKay
(@lindskay)
Active Member
Topic starter answered:
RE:

Hello!

Thank you for your quick responses. I dried the filament, and printed out a first layer calibration. It's printing the same pillars with defaults right now, but I thought I would update the first layer cal. now!

Thank you in advance,

 

This post was modified před 2 years by LindsKay
Napsal : 19/08/2022 12:45 pm
LindsKay
(@lindskay)
Active Member
Topic starter answered:
RE: Stringing and Holes - HELP 🙁

And here's the re-print with system defaults (0.15 Quality preset, 20% infill) it looks like drying it did have a good effect on the holes, but still some nasty stringing and not-that smooth edges and top. 

 

Napsal : 19/08/2022 1:15 pm
Diem
 Diem
(@diem)
Illustrious Member

It looks like you can usefully dry the filament more.

Your first layer is on the low end of acceptable; that's ok, it'll be a little longer before you have to recalibrate for nozzle wear.  Have you returned thr first layer temperature to the Filamentum default?

And your belt tension is not as bad as I feared but it would still be worth printing this:

    https://www.prusaprinters.org/prints/46639-tension-meter-for-the-gt2-belts-of-i3-mk3s-or-prus

It MUST be printed in Prusament PETG or the spring tension will be wrong.

Cheerio,

Napsal : 19/08/2022 11:32 pm
LindsKay
(@lindskay)
Active Member
Topic starter answered:
RE: Stringing and Holes - HELP 🙁

Hello again friends, I've dried my filaments and even have a filament dryer now since it realized the humidity is actually super high! I printed with the defaults again with a raised z-calibration and there was some serious improvement! But still SOME stringing. I also tested the belt and its tight. Any recommendations? 

Napsal : 02/09/2022 3:36 pm
Share: