English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 99 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Layers vertically wavey like the origin shifts... Von Big Stinky Cat... on Sep 19, 20 2476 2 Big Stinky Ca... Circle problems Von MightWorks on Sep 19, 20 5746 12 marcodl722 Prusa Slicer PLA print fan speed causes Therma... Von cwbullet on Sep 18, 20 4726 6 philip.b4 Correct first layer height for PETG Answered Von Metikumi on Sep 18, 20 7736 3 Metikumi PLA Severe stringing and blobbing on nozzle Von bobstro on Sep 17, 20 9739 10 el Guapo Layers not aligned Von Marco on Sep 17, 20 2365 5 Marco Unsuccessful solving X-axis error during self ... Von Danny_G on Sep 17, 20 3835 6 JUNO3D My 1st Benchy Von RH_Dreambox on Sep 15, 20 1501 4 Philip T repeating pattern Von haris on Sep 14, 20 1551 4 haris Problems with first prints Von Roger on Sep 14, 20 2035 7 Roger PLA building up around nozzle/sticking to nozz... Von bobstro on Sep 14, 20 4365 4 Mschenk903 probléme impression....spagettis après plusieu... Von anne on Sep 14, 20 1682 5 anne First 3D printer, first print. Bottom ok? Von carguy84 on Sep 14, 20 1642 6 carguy84 First Layer Calibration Fails, not enough fila... Von skout on Sep 13, 20 3263 8 skout Strange shifting behavior--any ideas? Von JoanTabb on Sep 12, 20 1530 2 MightWorks Prints support get loose / prints are knocked ... Answered Von JoanTabb on Sep 11, 20 4341 7 Marco Thickness of an official Prusa cable tie Von brian.m10 on Sep 11, 20 1816 3 brian.m10 Prints are a Little Wonky 🙁 Von Nick Fakeman on Sep 10, 20 1904 2 Nick Fakeman First PETG print made a mess - can I print wit... Von Tim G on Sep 10, 20 4938 7 Tim G Potato Chip (Parts pulling up off the bed) Von Rocket Bison on Sep 10, 20 3939 3 Vegas Pay LLC Seite 99 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: