English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 99 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author Layers vertically wavey like the origin shifts... Par Big Stinky Cat... on Sep 19, 20 2479 2 Big Stinky Ca... Circle problems Par MightWorks on Sep 19, 20 5753 12 marcodl722 Prusa Slicer PLA print fan speed causes Therma... Par cwbullet on Sep 18, 20 4731 6 philip.b4 Correct first layer height for PETG Answered Par Metikumi on Sep 18, 20 7745 3 Metikumi PLA Severe stringing and blobbing on nozzle Par bobstro on Sep 17, 20 9745 10 el Guapo Layers not aligned Par Marco on Sep 17, 20 2368 5 Marco Unsuccessful solving X-axis error during self ... Par Danny_G on Sep 17, 20 3842 6 JUNO3D My 1st Benchy Par RH_Dreambox on Sep 15, 20 1506 4 Philip T repeating pattern Par haris on Sep 14, 20 1552 4 haris Problems with first prints Par Roger on Sep 14, 20 2037 7 Roger PLA building up around nozzle/sticking to nozz... Par bobstro on Sep 14, 20 4365 4 Mschenk903 probléme impression....spagettis après plusieu... Par anne on Sep 14, 20 1684 5 anne First 3D printer, first print. Bottom ok? Par carguy84 on Sep 14, 20 1644 6 carguy84 First Layer Calibration Fails, not enough fila... Par skout on Sep 13, 20 3264 8 skout Strange shifting behavior--any ideas? Par JoanTabb on Sep 12, 20 1532 2 MightWorks Prints support get loose / prints are knocked ... Answered Par JoanTabb on Sep 11, 20 4345 7 Marco Thickness of an official Prusa cable tie Par brian.m10 on Sep 11, 20 1817 3 brian.m10 Prints are a Little Wonky 🙁 Par Nick Fakeman on Sep 10, 20 1906 2 Nick Fakeman First PETG print made a mess - can I print wit... Par Tim G on Sep 10, 20 4945 7 Tim G Potato Chip (Parts pulling up off the bed) Par Rocket Bison on Sep 10, 20 3943 3 Vegas Pay LLC Page 99 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :