English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 82 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Just assembled - garbled text, AutoLoad filame... Przez ff_7070 on Jan 31, 21 2242 5 ff_7070 Problem with self test: heater/thermistor not ... Przez Yu Tang on Jan 31, 21 3477 4 tshonka Help with first print - No luck at all. Przez cwbullet on Jan 31, 21 1772 9 dauga Creaking noise with PETG filament Przez Sam on Jan 31, 21 5401 9 Sam Y Axis Belt Alignment Problems Przez senga9872 on Jan 31, 21 4213 7 senga9872 How do I get reliable prints? Przez Sam on Jan 30, 21 1690 4 scottblanc ptfe jam Przez Sam on Jan 30, 21 2017 2 haris Pretest Przez lapf on Jan 30, 21 1645 3 lapf Creaking of the nozzle about the product Przez RH_Dreambox on Jan 30, 21 1988 6 Daniel i3 MK3S+ Kit Layers Problems Przez cwbullet on Jan 30, 21 2107 2 JoshyMade Nozzle hitting at the end of the print? Przez JoanTabb on Jan 29, 21 2877 6 DadOf6 Lost in Z translation - late first layer troub... Przez Dan Rogers on Jan 29, 21 2029 9 Furby Goulag Worked great, until it didn't Przez Dan Rogers on Jan 28, 21 1564 5 BlondCE First two Benchys - am I on the right track? Przez DanMi on Jan 28, 21 1246 3 DanMi Z Error following Hot End Replacement Przez Mark A on Jan 28, 21 1598 4 Mark A Optimal live-z setting not the same everywhere... Przez Husflid on Jan 28, 21 1804 5 Husflid First print vase from sd card inside not good Przez DadOf6 on Jan 28, 21 2507 3 TommyB Top layer tweaking Przez bobstro on Jan 27, 21 1982 5 KjsiderPrinte... First Layer issues: Live Z really high (or low... Przez KjsiderPrinter on Jan 27, 21 2500 17 KjsiderPrinte... First Layer Adhesion issue after 100+ successf... Przez Grayson72 on Jan 27, 21 2902 11 foxten Strona 82 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: