English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 68 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author New Build - Z Height is way off, cant get thro... Da cdrom1028 on Jun 02, 21 1543 3 cdrom1028 First time printer. calibration troubleshootin... Da cwbullet on Jun 02, 21 3889 16 Nic Heat break was found cross threaded after many... Answered Da Igmu on Jun 02, 21 1871 6 Igmu Issue with vertical lines and ghosting Da Dan Rogers on Jun 01, 21 2279 2 John Ryan 3d Benchy layer issues Da Marvin on May 31, 21 6271 13 buud Filament loading and unloading Da daSpud on May 31, 21 4663 13 h.herberg New member: Built the M3KS kit, printed a Benc... Da charlieporker on May 30, 21 2401 5 charlieporker Brim won't stick? Da ssill2 on May 29, 21 2484 4 Dan Cooper New Member - Just assembled, tested, calibrate... Da Grok on May 29, 21 1893 7 Grok first print feedback Da Greg on May 28, 21 1343 6 Greg Preassembled fans not working Da Peter M on May 28, 21 1663 5 djl Cant get a good print Da -- on May 27, 21 1685 10 bisketti Top Layer Issues, X and Y Surface Quality Ques... Da -- on May 26, 21 3238 18 aykunsezer X Axis Failing Selftest, slight resistance at ... Answered Da h.herberg on May 26, 21 2755 9 TheSargKyle z calibration fails no matter what I try Da MegardStudio on May 25, 21 3033 17 MegardStudio Strange noise when printing - MK3S+ Da Carlos Alberto on May 25, 21 2617 6 Carlos Albert... Horizontal Circles not round Da -- on May 25, 21 4714 8 PatrickM Filament not going in, new printer Da -- on May 25, 21 2333 11 Cold_Taco loose hotend? Da cwbullet on May 24, 21 5694 21 joe5939 Issue with printing with other brand PLA Da Ara on May 24, 21 1823 4 Ara Pagina 68 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: