English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 67 / 216 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Next Topic Title Last Post Views Posts Author Cant get a good print By -- on May 27, 21 1187 10 bisketti Top Layer Issues, X and Y Surface Quality Ques... By -- on May 26, 21 2341 18 aykunsezer X Axis Failing Selftest, slight resistance at ... Answered By h.herberg on May 26, 21 2076 9 TheSargKyle z calibration fails no matter what I try By MegardStudio on May 25, 21 2102 17 MegardStudio Strange noise when printing - MK3S+ By Carlos Alberto on May 25, 21 2013 6 Carlos Albert... Horizontal Circles not round By -- on May 25, 21 3460 8 PatrickM Filament not going in, new printer By -- on May 25, 21 1809 11 Cold_Taco loose hotend? By cwbullet on May 24, 21 4075 21 joe5939 Issue with printing with other brand PLA By Ara on May 24, 21 1399 4 Ara What is wrong with this pic? By cwbullet on May 23, 21 4906 44 Sink Extruder problem - new printer By cwbullet on May 23, 21 1123 10 Vita Black plastic collet By eng.shaimaa.el... on May 23, 21 2297 20 eng.shaimaa.e... Sloppy Delivery - Getting too big? By cwbullet on May 22, 21 1646 7 Sink filament sensor By cwbullet on May 22, 21 1077 4 wes Print defect mostly along one axis By cwbullet on May 22, 21 962 4 hamgolfer Repacking Misumi Bearings .. Replacing the fac... By cwbullet on May 21, 21 1845 3 Sink Extruder Body: Stuck screw and Spinning M3NS n... By MinorMatt on May 21, 21 3009 4 Seraphsins First Self-Test Failing at Bed Check By -- on May 20, 21 2525 2 Nyvad Large gaps on the seam Answered By DoctorShtein on May 19, 21 10818 8 DoctorShtein Extruder scoring the upper x-axis smooth rod? By -- on May 18, 21 3729 32 Frank Page 67 / 216 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Next Share: