English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 56 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Excessive (and seemingly deliberate) oozing on... By BogdanH on Oct 16, 21 3449 15 cdsupina X-axis rod damage after 50 hrs: Misaligned rod... By pcweber on Oct 16, 21 3336 7 Fourninetysix First Layer Printing Problem By Dan Rogers on Oct 15, 21 2059 13 seehma Visible Layer Lines/Arch Support By PrntrFiend on Oct 14, 21 2538 4 PrntrFiend Filament transport - looks like a snake swallo... By Sparkpoint on Oct 13, 21 2303 11 Sparkpoint Searching for the fancy calibration/setup post By dceddia on Oct 12, 21 1376 1 dceddia Initial switch on failure By Dan Rogers on Oct 12, 21 2687 15 John Leaking again By Dan Rogers on Oct 12, 21 2411 8 gamefe X shifting at same height By gamefe on Oct 10, 21 3907 16 gamefe Help! By JoanTabb on Oct 10, 21 1623 4 Kelly what is causing this defect in both abs and pl... By Dan Rogers on Oct 10, 21 2475 11 jrdpiper Extruder motor quite hot By karl-herbert on Oct 09, 21 2237 3 Rafi Filament covering extruder - help! By jwvaughn on Oct 09, 21 2065 6 HappyKatz Flipped pully to get Y-Axis central. Is this O... By Larry on Oct 08, 21 1514 6 Larry MK3S+ Kit. Help I broke the EXTRUDER CABLE CLI... By cwbullet on Oct 08, 21 1678 3 Jrmcswain Layer shift after infill By Sprite001 on Oct 07, 21 3642 11 nivek90 Brand new assembled MK3S+ making grinding nois... By Dan Rogers on Oct 07, 21 1517 4 drpepper How to assembly right? By Dan Rogers on Oct 07, 21 2205 16 PrusaPrinters... Issue with Globing By Josh Cagle on Oct 06, 21 1631 4 Josh Cagle Part thickness innacuracy. By SebastienMontp... on Oct 06, 21 1719 18 SebastienMont... Page 56 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: