English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 25 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Bad quality problem (MK3S) Da York Damon on Dec 19, 22 2043 9 Poli Poor Surface Finish Answered Da Solidev on Dec 19, 22 1185 5 Solidev First layer irregularities Da JoanTabb on Dec 19, 22 1345 5 Coffee Black Unable to print Answered Da Mark4E on Dec 18, 22 1228 8 Dav27 Print is all over the place - suggestions plea... Da RandyM9 on Dec 18, 22 1431 12 Ross Kay Tools Da Diem on Dec 17, 22 1266 7 Ross Kay 2 year old i3 MK3S+ lost calibration this morn... Answered Da gt7599a on Dec 16, 22 1282 4 gt7599a A question about regular maintenance time Answered Da Hello on Dec 15, 22 1488 6 4XS Strange layer shift error Answered Da RandyM9 on Dec 15, 22 1354 9 4XS Part of Print Lifting off the plate Da Sanreb on Dec 15, 22 1729 14 Sanreb Incorrect printer? Da Salty Reign on Dec 14, 22 1613 9 Salty Reign Continuous beep upon first start Da Thanh3D on Dec 14, 22 2195 4 Olomoucká díl... First Rokie Disaster 🙂 Oh My! Da Hello on Dec 14, 22 1243 4 Gordon Krum Plastic stuck on print head Da Diem on Dec 13, 22 2512 2 bartyoung Strange Prints - Help? Da Krabbelfiech on Dec 13, 22 918 1 Krabbelfiech Y-axis bearing bolt touching bed from below Da Netpackrat on Dec 12, 22 1365 8 Ratman Initial layer sticks but after a few minutes i... Da Sanreb on Dec 11, 22 4488 17 Sanreb Intermittent Printing Issues Answered Da Solidev on Dec 10, 22 1586 10 Solidev X-Axis Stepper Motor DOA Da Straight_Haste on Dec 09, 22 1212 5 Straight_Hast... Unable to print petg Da Crab on Dec 08, 22 1012 2 MARTIN65 Pagina 25 / 216 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Avanti Condividi: