English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 212 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author First Layer Problems Od stahlfabrik on May 14, 18 2179 3 joseph.l6 de-grease and re-grease of linear bearings Od reid.b on May 13, 18 2709 3 Michael K. First prints taking ~40% longer than expected Od Olef on May 12, 18 1818 2 Peter Move Z < 1 mm Od sam.b on May 11, 18 2290 3 sam.b Extruder knocking/ clicking. Od Joe on May 11, 18 1623 5 Joe Top surface uneven Od Martin Wolfe on May 10, 18 2092 5 twam newbie, terrible prints - clueless whats wrong Od duncan.c3 on May 10, 18 2048 5 duncan.c3 [Need Support] Frequent Filament Jams Od thrawn86 on May 09, 18 2194 5 Timothy Graup... Self Test fails Od Jotech on May 09, 18 1521 3 Jotech Third print issue. Od richard.l on May 09, 18 808 7 Rudel live Z too low? Od reid.b on May 08, 18 2159 3 Gato Expected noise? Od BradW on May 08, 18 1895 7 Gato New Mk3 shifting layers Od Mark McGraw on May 07, 18 2532 10 Mark McGraw [SOLVED] Extruder slipping from hotend jam Od Timothy Graupm... on May 07, 18 2757 9 Timothy Graup... Waves on the first layer Od JoanTabb on May 07, 18 2322 5 Mike Eberlein z axis failing after adjusting belts Od Gato on May 07, 18 1641 3 Gato Nozzle touch print Od Kevin Setz on May 06, 18 1818 4 Kevin Setz Assorted Printing Problems Od thrawn86 on May 06, 18 1856 2 harrison.y Best bed type for Polycarbonate? Od thrawn86 on May 06, 18 2635 2 tyler.h8 Noob - Need assistance fine tunig Od thrawn86 on May 06, 18 1662 2 Wally Stránka 212 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: