English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 210 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Is this a problem with my X belt tension? By JoanTabb on May 26, 18 1950 5 curt.h Newb, Printed some tests - Can you help me int... By Dibujor on May 26, 18 8594 28 Dibujor Loose X and Y axis belts. How to tighten them? By Gato on May 25, 18 15581 6 luca.r Go from bad to worse By mark.m51 on May 23, 18 1303 1 mark.m51 filament doesnt stick to bed By LaPointe on May 22, 18 1448 3 Jákup J. E. Bed level issues By LaPointe on May 22, 18 2812 5 Gradivus new kit build: bottom and top layer issues By Dibujor on May 22, 18 1959 6 blueicee X-axis shift By narloke on May 22, 18 2543 8 narloke Cooling Fan Error By Fotoman on May 22, 18 2009 4 Fotoman Replacing the X end motor-idler and tightening... By thrawn86 on May 22, 18 2757 2 Oram & Ra... build plate By LaPointe on May 21, 18 1358 2 mark.g22 XYZ calibration looks like it finds all 4 poin... By jon.k on May 21, 18 3460 10 jon.k Filament Jam By christian.m23 on May 21, 18 1723 10 christian.m23 Heat Bed Temperature By Olef on May 21, 18 1744 4 Beech76 PETG cold pulls By Gato on May 20, 18 26445 7 devilhunter Adhesion issues By LaPointe on May 20, 18 1777 5 mark.m51 Use drill for assembly? By Gato on May 20, 18 2851 9 Gato extruder clicks and leaves gaps in dispensed f... By thrawn86 on May 20, 18 1782 4 dimprov Crash detected.. resumed with a layer shift. By blueicee on May 19, 18 1222 5 dat1darkrai Severe Y-Axis Skipping/Shiftin By Rosparovac on May 19, 18 1671 2 eric.s32 Page 210 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: