English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 204 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Yet another print issue. Przez joe.w6 on Jul 10, 18 1493 11 joe.w6 First PETG print, is it ok? Przez thrawn86 on Jul 10, 18 1603 5 nathan0876 LOST HOME ! Przez christian.m23 on Jul 09, 18 4185 8 christian.m23 Live Z adjust missing Przez bobstro on Jul 08, 18 1842 2 orlins Horizontal Banding Issue Przez themzlab on Jul 08, 18 3041 3 aleks.z When good filament goes bad... Przez stoofer on Jul 08, 18 622 1 stoofer High value needed in Live-Z Adjustment to prin... Przez peter.k40 on Jul 08, 18 1558 8 Aaron Theesfe... Extruder calibration attempts to overextrude Przez trent.j on Jul 08, 18 1503 2 trent.j Pinda always fails on third calibration Przez themzlab on Jul 07, 18 1576 4 joe.h5 Only one z-axis motor works Przez JMAC on Jul 07, 18 3808 8 robotdad first layer adjustment help Przez Dibujor on Jul 05, 18 2038 5 Kagekitsune No power, only whining Przez Fotoman on Jul 05, 18 1897 3 joe.h5 Filament Jams Przez Pathogen on Jul 05, 18 1351 3 Pathogen Need help! Just assembled MK3 kit prints are n... Przez Peter in Katy on Jul 04, 18 1361 6 Jeffro New assemble (I3/Mk3) - Wizard reboot cycle - ... Przez DougS on Jul 03, 18 483 3 DougS Various issues with first prints Przez bobstro on Jul 03, 18 2049 6 paul.a13 First Logo Print - OK or not OK? Przez michaelrommel on Jul 02, 18 2713 7 michaelrommel First print complete, opinions? Przez nathan0876 on Jul 02, 18 2428 9 nathan0876 XYZ Failing - Endstops Przez Klaas on Jul 02, 18 2711 5 Veggysaurus Build kit as is or into IKEA Lack directly? Przez Asraff Amzani on Jul 01, 18 2375 4 Tellblom Strona 204 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: