English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 204 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Any idea what causes this? Od RufusClupea on Jul 13, 18 1887 2 Lique Hanging bits of filament - overextrusion? Od travis.c5 on Jul 13, 18 2505 4 rhjpires Bad brim - what to do? Od JoanTabb on Jul 13, 18 10279 6 Eirik steel sheet cover Od Kai on Jul 12, 18 1735 2 PaZi Any idea what is causing this? Od Kai on Jul 12, 18 3024 8 corycwagner good first layer? Od JoanTabb on Jul 12, 18 1813 4 Kagekitsune (resolved) Calibration Failed check The axes a... Od Joe on Jul 11, 18 946 1 Joe How do my first prints look? Od Barry on Jul 11, 18 2093 3 Barry Y-Axis Uneveness Od rory.w on Jul 10, 18 1729 3 rory.w Yet another print issue. Od joe.w6 on Jul 10, 18 1625 11 joe.w6 First PETG print, is it ok? Od thrawn86 on Jul 10, 18 1891 5 nathan0876 LOST HOME ! Od christian.m23 on Jul 09, 18 4716 8 christian.m23 Live Z adjust missing Od bobstro on Jul 08, 18 2073 2 orlins Horizontal Banding Issue Od themzlab on Jul 08, 18 3358 3 aleks.z When good filament goes bad... Od stoofer on Jul 08, 18 690 1 stoofer High value needed in Live-Z Adjustment to prin... Od peter.k40 on Jul 08, 18 1740 8 Aaron Theesfe... Extruder calibration attempts to overextrude Od trent.j on Jul 08, 18 1698 2 trent.j Pinda always fails on third calibration Od themzlab on Jul 07, 18 1749 4 joe.h5 Only one z-axis motor works Od JMAC on Jul 07, 18 4248 8 robotdad first layer adjustment help Od Dibujor on Jul 05, 18 2252 5 Kagekitsune Stránka 204 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Share: