English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 203 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Textile wrap on heatbed cables coming loose Przez paul.a13 on Jul 16, 18 1963 5 paul.a13 Filament stuck in the hot end?! Przez LaPointe on Jul 15, 18 2884 5 christie.l First layer irregularities Przez LaPointe on Jul 15, 18 1767 2 simon.l15 Overextrude or what happen to my print? Przez devilhunter on Jul 14, 18 2072 6 Ingo H. Holes in solid infill Przez tomp on Jul 14, 18 2583 4 tomp Extrusion issue Przez Dingolingo on Jul 14, 18 2876 9 Dingolingo PSU Squealing? Przez Raquor on Jul 13, 18 1620 2 Raquor Any idea what causes this? Przez RufusClupea on Jul 13, 18 1618 2 Lique Hanging bits of filament - overextrusion? Przez travis.c5 on Jul 13, 18 2190 4 rhjpires Bad brim - what to do? Przez JoanTabb on Jul 13, 18 8930 6 Eirik steel sheet cover Przez Kai on Jul 12, 18 1442 2 PaZi Any idea what is causing this? Przez Kai on Jul 12, 18 2702 8 corycwagner good first layer? Przez JoanTabb on Jul 12, 18 1566 4 Kagekitsune (resolved) Calibration Failed check The axes a... Przez Joe on Jul 11, 18 833 1 Joe How do my first prints look? Przez Barry on Jul 11, 18 1806 3 Barry Y-Axis Uneveness Przez rory.w on Jul 10, 18 1458 3 rory.w Yet another print issue. Przez joe.w6 on Jul 10, 18 1449 11 joe.w6 First PETG print, is it ok? Przez thrawn86 on Jul 10, 18 1505 5 nathan0876 LOST HOME ! Przez christian.m23 on Jul 09, 18 3984 8 christian.m23 Live Z adjust missing Przez bobstro on Jul 08, 18 1730 2 orlins Strona 203 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: