English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 189 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Askew Printing Von NTX9 on Oct 22, 18 2495 4 michael.n27 After filament load it don't stop extruding ev... Von Mustrum Ridcul... on Oct 20, 18 4966 7 Nessuno0505 Calibration failed - check axes Von Julian on Oct 20, 18 6016 6 Justin First Layer Von michael.n27 on Oct 20, 18 1841 3 michael.n27 Layer shifting or something else? Von michael.n27 on Oct 20, 18 1664 3 kathleen.f2 Even line spiraling around a round object Von Neal on Oct 19, 18 1876 8 chriskkk Printer to loud Von bobstro on Oct 18, 18 2151 2 Laire XY first calibration failed - check the manual Von JBinFL on Oct 18, 18 6545 25 Nessuno0505 Prusa i3 Mk3 Help Required Von JoanTabb on Oct 17, 18 2111 3 ashish.g Top layer becoming bad Von remi.o on Oct 16, 18 1853 5 remi.o Layer shifting Von LaPointe on Oct 16, 18 2609 14 rachel-anne.h Good and bad print in one! Von bobstro on Oct 16, 18 1767 3 Fred Henaux Broken PINDA? Von svachalek on Oct 16, 18 1626 3 svachalek First layer printing blobs and strings after f... Von Mustrum Ridcul... on Oct 16, 18 2295 2 kevin.a18 Extruder wont go past 140 degree Von Pathogen on Oct 16, 18 1657 2 Pathogen Pause Print Von toaf on Oct 15, 18 1312 2 ktmcmo Assembled MK3 problems Von gminnick on Oct 15, 18 2621 10 amanul.h Initial setup layer heighth? Von markus.i2 on Oct 15, 18 1848 3 markus.i2 PINDA probe Von Olef on Oct 15, 18 1628 3 holten.c Room for improvement Von MostlyHarmless on Oct 14, 18 2660 7 markus.i2 Seite 189 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: