English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 189 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Layer shifting or something else? Przez michael.n27 on Oct 20, 18 1568 3 kathleen.f2 Even line spiraling around a round object Przez Neal on Oct 19, 18 1810 8 chriskkk Printer to loud Przez bobstro on Oct 18, 18 2057 2 Laire XY first calibration failed - check the manual Przez JBinFL on Oct 18, 18 6358 25 Nessuno0505 Prusa i3 Mk3 Help Required Przez JoanTabb on Oct 17, 18 1980 3 ashish.g Top layer becoming bad Przez remi.o on Oct 16, 18 1766 5 remi.o Layer shifting Przez LaPointe on Oct 16, 18 2534 14 rachel-anne.h Good and bad print in one! Przez bobstro on Oct 16, 18 1693 3 Fred Henaux Broken PINDA? Przez svachalek on Oct 16, 18 1541 3 svachalek First layer printing blobs and strings after f... Przez Mustrum Ridcul... on Oct 16, 18 2228 2 kevin.a18 Extruder wont go past 140 degree Przez Pathogen on Oct 16, 18 1592 2 Pathogen Pause Print Przez toaf on Oct 15, 18 1214 2 ktmcmo Assembled MK3 problems Przez gminnick on Oct 15, 18 2524 10 amanul.h Initial setup layer heighth? Przez markus.i2 on Oct 15, 18 1768 3 markus.i2 PINDA probe Przez Olef on Oct 15, 18 1558 3 holten.c Room for improvement Przez MostlyHarmless on Oct 14, 18 2563 7 markus.i2 inconsistent first layer Przez andy.b15 on Oct 14, 18 1498 2 Utsocknes IMpossible to get an Even First layer all over... Przez marto on Oct 14, 18 981 4 Christizzz seriously impressed with what the MK3 can do w... Przez Mustrum Ridcul... on Oct 14, 18 3316 11 Mustrum Ridcu... Extruder R3 seems too tight in PTFE tube Przez Mustrum Ridcul... on Oct 13, 18 1891 3 Henryhbk Strona 189 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: