English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 189 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Askew Printing Od NTX9 on Oct 22, 18 2493 4 michael.n27 After filament load it don't stop extruding ev... Od Mustrum Ridcul... on Oct 20, 18 4962 7 Nessuno0505 Calibration failed - check axes Od Julian on Oct 20, 18 6016 6 Justin First Layer Od michael.n27 on Oct 20, 18 1840 3 michael.n27 Layer shifting or something else? Od michael.n27 on Oct 20, 18 1663 3 kathleen.f2 Even line spiraling around a round object Od Neal on Oct 19, 18 1876 8 chriskkk Printer to loud Od bobstro on Oct 18, 18 2151 2 Laire XY first calibration failed - check the manual Od JBinFL on Oct 18, 18 6544 25 Nessuno0505 Prusa i3 Mk3 Help Required Od JoanTabb on Oct 17, 18 2110 3 ashish.g Top layer becoming bad Od remi.o on Oct 16, 18 1845 5 remi.o Layer shifting Od LaPointe on Oct 16, 18 2607 14 rachel-anne.h Good and bad print in one! Od bobstro on Oct 16, 18 1766 3 Fred Henaux Broken PINDA? Od svachalek on Oct 16, 18 1625 3 svachalek First layer printing blobs and strings after f... Od Mustrum Ridcul... on Oct 16, 18 2294 2 kevin.a18 Extruder wont go past 140 degree Od Pathogen on Oct 16, 18 1655 2 Pathogen Pause Print Od toaf on Oct 15, 18 1311 2 ktmcmo Assembled MK3 problems Od gminnick on Oct 15, 18 2617 10 amanul.h Initial setup layer heighth? Od markus.i2 on Oct 15, 18 1846 3 markus.i2 PINDA probe Od Olef on Oct 15, 18 1627 3 holten.c Room for improvement Od MostlyHarmless on Oct 14, 18 2660 7 markus.i2 Stránka 189 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: