English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 178 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Defective Z Axis Right Motor? Por grant.g5 on Jan 23, 19 1813 3 grant.g5 Slow death..... Por rob.l6 on Jan 23, 19 875 3 ian.m36 Help! "Calibration Failed! Check the axes... Por John K. on Jan 23, 19 1331 6 bpmarkowitz First boot calibration unable to load filament... Por Sukkubix on Jan 23, 19 1849 8 Sukkubix Xyz calibration fail Por Nikolai on Jan 22, 19 1869 5 stein-ivar.b Y-axis Layer drifting (not shifting?) Por Nairolf22 on Jan 22, 19 2769 8 Nairolf22 First Layer Height setting? Por Nikolai on Jan 22, 19 4376 4 Snardo Strange noise on change of direction diagonall... Por Steve on Jan 21, 19 3694 4 Steve Yellow PETG adhesion/density issues around lay... Por thomas.h59 on Jan 21, 19 2817 11 thomas.h59 PLA Bed Adhesion issues, Help! Por -- on Jan 21, 19 2638 4 Snardo Odd issue with higher layers on newly built ki... Por Bret on Jan 21, 19 1318 3 Bret Weird characters displayed during bed calibrat... Por Frank on Jan 21, 19 2154 4 Frank Some prints work, some don't Por Shelby Teknolo... on Jan 21, 19 1551 3 Shelby Teknol... Repair advice PRUSA I3 MK3 MULTI MATERIAL 2.0 Por Vegas Pay LLC on Jan 20, 19 1656 1 Vegas Pay LLC X axis binding and bottom 2 screws on X carria... Por jon bondy on Jan 20, 19 1675 3 jon bondy Strings more visible over time Por Felix on Jan 20, 19 1836 4 Felix XYZ Axis Calibration Error Por RH_Dreambox on Jan 20, 19 1354 2 Fuganater Zaxis problems Por RH_Dreambox on Jan 20, 19 1825 3 Max C. XYZ Axis Calibration Error at first point Por Joe on Jan 20, 19 2089 3 aaron.k13 Are my walls acceptably ‘smooth’? Por Nikolai on Jan 20, 19 3168 9 Adam Página 178 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: