English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 175 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author MK3S print colour Por Nikolai on Feb 15, 19 1306 4 Neil Ramsay No assembly manual included now? Por david.p104 on Feb 15, 19 1916 4 david.p104 Cannot unscrew heatsink from hotend... Por -- on Feb 14, 19 1871 8 daniel.e24 mk3 Kit scraping on infil (newb) Por rob.l6 on Feb 14, 19 2336 6 frynryan This sound is driving me CRAZY Por -- on Feb 14, 19 2353 8 matthew.m63 Extruder too tight, even with door open... Por daniel.e24 on Feb 13, 19 1072 3 daniel.e24 missing/wrong part Por Mtnbike on Feb 12, 19 2098 8 Mtnbike Heater / Thermistor not connected. Por diego.p11 on Feb 11, 19 2480 10 jimosity my 1st print with my new MK3 Por Nikolai on Feb 11, 19 1677 3 gb XYZ calibration - printer stops right after de... Por Highlander on Feb 10, 19 2567 5 Polan MK3 Stops during print Por -- on Feb 09, 19 1658 4 ingo.b What to do after your very first print (mainte... Por d.l on Feb 09, 19 3092 4 d.l first layer cal uneven on left & right sid... Por tj on Feb 09, 19 2477 4 tj Extruder Frustrations Por Martin_au on Feb 08, 19 2733 14 christian.s55 Strain relief won't allow CPU door to shut. Por jesse.m9 on Feb 07, 19 699 4 jesse.m9 Help me figure out the problem Por timo.m on Feb 07, 19 1398 6 BadFuse First Print! X-axis issue? Any ideas? Por fraley on Feb 07, 19 2307 7 fraley Another Y-axis Drift Por -- on Feb 07, 19 2343 5 ItsAMeMario Artifacts on Benchy Por Endymion on Feb 07, 19 2270 5 Endymion X-axis layer shift that resolved itself? Por geoff.h6 on Feb 07, 19 1803 5 geoff.h6 Página 175 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: