English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 174 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Y axis Bearings By james.r49 on Feb 23, 19 1791 4 james.r49 intermittent X axis crash By vintagepc on Feb 22, 19 3925 13 jason.q2 Temperature Tower By -- on Feb 22, 19 4193 7 Doug Bailey PEI sheet lifted off bed after removing print By -- on Feb 21, 19 3946 7 drewthat PFTE Lenght By flioink on Feb 21, 19 1636 4 gatonini@zoom... Printable Part...prints to small? By Dimokin on Feb 21, 19 920 2 Dimokin Anyone else having the error with the printer ... By alexander.s27 on Feb 21, 19 1697 2 chota.b Potential warped bed? By Dave Jackson on Feb 21, 19 1644 2 matthew.c59 Surface problems after reassembling the Extrud... By thomas.s110 on Feb 21, 19 1458 4 thomas.s110 Power supply voltage By DaJMasta on Feb 21, 19 3913 3 joaquin.o3 Bed Level Correction: Clarification of zones. By -- on Feb 20, 19 816 4 GizmoGorilla Correct steps to remove jammed filament By flioink on Feb 20, 19 3557 10 flioink Calibration Failed (Check Axes) at start of ca... By Anzen on Feb 20, 19 2203 4 joel.p How long did assembly take By hdhc on Feb 19, 19 14987 20 chad.k6 MK3 first print need some feedback By john.m138 on Feb 19, 19 2318 5 john.m138 Difficulty with TPU By Robin on Feb 19, 19 2557 11 STSanford y-rod-holder.stl By -- on Feb 19, 19 2307 2 nsand U.S. source for spacers for the heatbed? By kurzondax on Feb 18, 19 2475 12 kurzondax X Axis is way too loud? By -- on Feb 18, 19 3075 5 Jaxel Mk3 Nozzle leaks after print begins By -- on Feb 18, 19 1956 4 zjdoliver Page 174 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: