English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 170 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author First print and PETG filament Por Chocki on Mar 12, 19 2004 8 krilleric Is it necesary the XYZ calibration? Por ManelTo on Mar 12, 19 1967 7 ManelTo layershifting consistent between 3rd and 4th l... Por neroes on Mar 12, 19 2301 19 neroes First time printing ABS, some noob questions :... Por Nikolai on Mar 12, 19 1523 3 Diemux Freshly built mk3s and stock gcode. What am I ... Por -- on Mar 12, 19 2125 7 Heli3D MK3S upgrade - cannot get extruder thermistor ... Por talz13 on Mar 12, 19 2223 3 talz13 MK3S Y axis GT2-16 Pulley misalignment Por Bunny Science on Mar 12, 19 1750 2 Tanner Sorens... Mk3s stops print halfway and filament breaks a... Por Jon_G on Mar 12, 19 2012 10 zen.k Heatbed screws not flush Por vintagepc on Mar 11, 19 1717 5 Taldaas Newbie Por -- on Mar 11, 19 1738 2 Skipper_52 First Print Surface finish issue Por Rocky79 on Mar 11, 19 1690 5 Rocky79 trapezoidal nuts Por JoanTabb on Mar 11, 19 1605 2 Brankomer X-axis dont move smooth on z-axis Por Brankomer on Mar 11, 19 2324 4 Brankomer I need help Por Heli3D on Mar 11, 19 1669 6 Heli3D X axis bearings sticky Por -- on Mar 10, 19 2912 4 Gavin First layer falling apart with Prusament PETG Por vintagepc on Mar 10, 19 1705 5 evan.z callibrating problem after update to 3.6.0. Por bobstro on Mar 10, 19 781 2 Albert Self test - Heater/Thermistor not connected Por Mike J on Mar 10, 19 6065 5 Mike J Printer loosing home point? Por JBinFL on Mar 10, 19 3819 14 ronald.t6 Pattern on the heatbed steel sheet Por JBinFL on Mar 10, 19 2097 7 krilleric Página 170 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: