English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 165 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Need some help for bad printing By Filnet on Apr 09, 19 1363 4 Filnet MK3S Kit Z Calibration Not Moving By andrew.j15 on Apr 09, 19 2684 15 steven.w24 Unable to run the Calibration Menu’s First Lay... By arkowal4 on Apr 09, 19 1526 2 arkowal4 mk3s stops printing halfway when using prusa s... By -- on Apr 08, 19 1724 4 zen.k Newbie: Prints GOOD, except first 3-4 layers?? By redherring9 on Apr 08, 19 2007 8 redherring9 Dimensional accuracy requirement of Prusa prin... By RetireeJay on Apr 07, 19 1883 3 Sravan Mettup... MK3S upgrade to IR sensor unable to calibrate By Mustrum Ridcul... on Apr 07, 19 2017 4 Valiran New Assembly, Unable to Connect via Pronterfac... By Mustrum Ridcul... on Apr 07, 19 1799 2 C. O. Z-Calibration Failure after Originially Workin... By -- on Apr 06, 19 2336 10 Lumbermouth PTFE Tube on Hotend Assembly too long? By Grandpa Joe on Apr 05, 19 3992 6 daniel.e24 assembling year old MK3 kit: anything to updat... By Sravan Mettupa... on Apr 05, 19 2323 14 Sravan Mettup... Left hotend fan? Spinning, Not Spinning? MK3 By fuco on Apr 05, 19 11512 24 michael.p77 Z axis belt alignment. By Kai on Apr 04, 19 835 4 william.a12 First layer creates wavy uneven lines By bobstro on Apr 03, 19 3270 2 damion fusco Problems with very new printer (DIY KIT) By holmes4 on Apr 03, 19 2188 11 Merinto Oh look another stripped grub screw post By -- on Apr 03, 19 4214 15 matt.b28 Filament bends around the nozzle By Desti on Apr 02, 19 2261 6 Desti Can someone help me with what I may have set w... By bobstro on Apr 02, 19 1891 9 jack.c5 Warped Y frame or Heatbed? By -- on Apr 02, 19 2224 2 nubbyninja occasional last layer weirdness By Wout on Mar 31, 19 1690 6 Wout Page 165 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: