English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 164 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Artifacts on side of included benchy Von Abiathar on Apr 20, 19 3631 9 Abiathar Z height Von jeremy.p19 on Apr 20, 19 1792 4 jeremy.p19 This can't be right... Von cwbullet on Apr 20, 19 1186 13 John Dupras PLA adhesion issue & question Von -- on Apr 20, 19 4466 12 CyberBiker Unable To Get Decent Prints Von Enverex on Apr 20, 19 3178 9 Enverex SD Card Benchy a Hot Mess (DIY Kit) Von -- on Apr 19, 19 3299 15 derek.p11 Printer problems after cancelled print Von james.c79 on Apr 19, 19 3709 8 james.c79 newly assembled MK3S issues - z-leveling enfor... Von Pbelcomp on Apr 19, 19 3158 15 Edward B New Filament Sensor Error again Von holmes4 on Apr 18, 19 1768 2 Lups X axis not parallel to bed if I use the top pa... Von 666dsa666 on Apr 18, 19 2155 5 666dsa666 First layer hight issue Von Endymion on Apr 18, 19 2752 10 Lups Scarring on top surface Von ElFroCampeador on Apr 18, 19 17132 59 ElFroCampeado... Uneven print after successful calibration Von Mustrum Ridcul... on Apr 17, 19 1756 3 jessica.j3 Layer shifting Von jan.l29 on Apr 17, 19 1713 2 jan.l29 Slumping Print Suggestions Von -- on Apr 17, 19 1373 2 david.j47 Mk3 + Mk3s Upgrade + MMU assembly Von K7ZPJ on Apr 16, 19 2117 4 damien.d2 After MK3S MMU2S ugrade - fails to load filame... Von Franz on Apr 16, 19 1480 2 Jerry Siegel Print pausing in mid run Von JMHaro on Apr 16, 19 2212 10 JMHaro MK3S Upgrade - Extruder Heater cable removal Von vintagepc on Apr 14, 19 2301 3 OctoPope Bad prints Von toaf on Apr 14, 19 2619 8 henry.f3 Seite 164 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Teilen: