English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 161 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Why only 3 bearings for the Y bed? Por gnat on May 06, 19 4068 17 gnat cannot find support hotline? Por bobstro on May 06, 19 2036 4 josef min temp error. Por Vojtěch on May 06, 19 4113 22 Frankinstine First Layer Issues Por Vojtěch on May 06, 19 1667 6 christian.s55 MK3S, FW3.7.0-2201, XYZ Calibration fails regu... Por Vojtěch on May 05, 19 1854 5 Jo Failing large prints Por Peter M on May 05, 19 1495 4 rosenstand Weird sound from printer. Por Mike on May 05, 19 2016 6 Mike Did a Micro-All-In-One-Test. Tips for improvin... Por bobstro on May 04, 19 3892 4 Funkymonkey PETG problems after partial MK3 -> MK3S + MMU2... Por gnat on May 04, 19 1869 5 gnat First Layer calibration is hair thin. Por vintagepc on May 04, 19 3996 8 Sir Fico Very stuck on first layer calibration Por Funkymonkey on May 04, 19 4651 18 Funkymonkey Lines out of place in first print Por JR Gonzalez on May 03, 19 2035 7 JR Gonzalez What is wrong with first test print? Por Andybx on May 03, 19 2021 11 Andybx Spun nut Por Jason Tibbitts on May 03, 19 2315 5 Jason Tibbitt... Mesh Bed Leveling and Poor Prints Por vintagepc on May 03, 19 2457 13 jonathan.d30 Prusa I3 Mk3 Regular gaps in print. Por Andybx on May 03, 19 2236 10 graham.m5 Mk3s stops multiple times requesting filament ... Por Andreas on May 03, 19 1402 3 TMH Quality print question ... Por -- on May 02, 19 1472 3 yannick.e New printer Por -- on May 02, 19 1853 5 Spoon Fixing broken wires on Heater Cartridge Por vintagepc on May 01, 19 9880 6 Kvatthro Página 161 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: