English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 160 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author First layer calibration error. First time user... Da Arcannys on May 18, 19 1659 1 Arcannys What is the expected i3 mk3S extruder motor te... Da GregB on May 18, 19 3230 13 GregB First build problem Da Cyranova on May 18, 19 1443 1 Cyranova First layer issue at some specific bed area Answered Da Vojtěch on May 17, 19 5992 22 Mallonum Failed XYZ Calibration Da 2002superhawk on May 17, 19 2595 13 2002superhawk Had to replace PTFE, now going backwards, prin... Da Nigel on May 17, 19 3141 11 redherring9 What material are the components? Da Vojtěch on May 16, 19 4493 5 john.c52 Extrusion slows and stops at a predictable poi... Da GregB on May 16, 19 2821 19 GregB Assembly X-axis smooth rod issue Da Vojtěch on May 16, 19 2354 3 brightwing Selftest print fan failure Da Shelby Teknolo... on May 15, 19 2131 3 Shelby Teknol... After installation, which program to use? Da -- on May 15, 19 1616 5 HoofedGibbon5... Had to replace hot end. Still not happy with p... Da -- on May 15, 19 1825 5 rachel.s5 Heavy printer problems because of under extrus... Da SiedlerK on May 14, 19 4219 11 SiedlerK Easy way to raise extruder out of the way afte... Da Chualzo on May 14, 19 10118 6 Chualzo error in the selftest: left fan Da Seb74 on May 14, 19 1813 3 carlos First Layer Cal one side higher than other Da TLowman92 on May 14, 19 3133 3 TLowman92 "Small" printing problem Da joey4711 on May 13, 19 2432 11 joey4711 Is there any way to purchase a tested extruder... Da GregB on May 13, 19 2487 6 GregB First layer, what is wrong? Da Peter M on May 12, 19 7145 29 svein Selftest Error Axis Length - Y Axis Da Johan on May 12, 19 2601 8 doug-1 Pagina 160 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Condividi: