English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 16 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Tytuł Tematu Ostatni Post Widok Posty Author Low PINDA, -2 Z offset Answered Przez Diem on Aug 08, 23 2354 5 Melissa Antho... Test prints evaluation pls Przez Michael Pieric... on Aug 03, 23 1999 7 Michael Pieri... Failed Calibration Cube Fail Przez Robin on Aug 02, 23 2387 4 Spencer Thurg... Help identifying artifacts Przez balt91 on Aug 01, 23 1784 1 balt91 0.6 Nozzle switch seam issues Przez pixelwave on Aug 01, 23 2174 6 pixelwave Why does Prusa not recommend lubricating the b... Przez n808 on Jul 29, 23 8400 28 n808 Is there an STL for the Prusa lubricant applic... Answered Przez tollopa on Jul 27, 23 5997 7 Grymjar Trapezoidal nuts missing? Przez JoanTabb on Jul 16, 23 2060 4 Michael Pieri... Belt Tension Przez Robin_13 on Jul 14, 23 2166 4 gorillamotors Z Banding? Inconsistent Layer Lines? Przez Diem on Jul 12, 23 3197 3 Yalemannec Loud continuous beep upon first startup Przez williamgray on Jul 11, 23 3994 2 Matthios Meng... Vibration Noise on Y-Axis Przez PartyPlatter08 on Jul 10, 23 5556 6 Lambi XYZ Calibration failed. Please consult the man... Przez Diem on Jul 08, 23 2062 2 digitiz Problem with sticky Y motor Przez Volker on Jul 06, 23 4218 9 BjornM Problem with 1st layer calibration Przez Diem on Jul 03, 23 2438 4 Adam Weird waves in my print Przez Robin on Jul 01, 23 2121 2 Tyler Issues with first layer calibration. Przez Robin on Jul 01, 23 2382 4 corb printer MK3S+ not started (repeat SETUP). Przez JoanTabb on Jun 25, 23 2517 4 Paweł Kaczmar... Calibration failed! Check the axes and run aga... Przez Enigma on Jun 25, 23 12326 9 nathasm "verticle blob" on first prints (mostly on pri... Przez Mike C on Jun 21, 23 2846 6 Mike C Strona 16 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Share: