English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 159 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author That Screw Przez Vojtěch on May 20, 19 2006 6 GregB First Start Error Przez Vojtěch on May 20, 19 1673 2 tok_on_prusa Second layer shifted lightly left of first lay... Przez chnicola on May 19, 19 1279 2 chnicola Total noobs experience with MK3S & question Przez HC093HE on May 19, 19 2452 17 HC093HE First layer calibration error. First time user... Przez Arcannys on May 18, 19 1452 1 Arcannys What is the expected i3 mk3S extruder motor te... Przez GregB on May 18, 19 2566 13 GregB First build problem Przez Cyranova on May 18, 19 1192 1 Cyranova First layer issue at some specific bed area Answered Przez Vojtěch on May 17, 19 4966 22 Desti Failed XYZ Calibration Przez 2002superhawk on May 17, 19 2188 13 2002superhawk Had to replace PTFE, now going backwards, prin... Przez Nigel on May 17, 19 2818 11 redherring9 What material are the components? Przez Vojtěch on May 16, 19 3949 5 john.c52 Extrusion slows and stops at a predictable poi... Przez GregB on May 16, 19 2517 19 GregB Assembly X-axis smooth rod issue Przez Vojtěch on May 16, 19 2059 3 brightwing Selftest print fan failure Przez Shelby Teknolo... on May 15, 19 1710 3 Shelby Teknol... After installation, which program to use? Przez -- on May 15, 19 1393 5 HoofedGibbon5... Had to replace hot end. Still not happy with p... Przez -- on May 15, 19 1550 5 rachel.s5 Heavy printer problems because of under extrus... Przez SiedlerK on May 14, 19 3861 11 SiedlerK Easy way to raise extruder out of the way afte... Przez Chualzo on May 14, 19 9308 6 Chualzo error in the selftest: left fan Przez Seb74 on May 14, 19 1505 3 carlos First Layer Cal one side higher than other Przez TLowman92 on May 14, 19 2801 3 TLowman92 Strona 159 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: