English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 159 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author That Screw Par Vojtěch on May 20, 19 2009 6 GregB First Start Error Par Vojtěch on May 20, 19 1674 2 tok_on_prusa Second layer shifted lightly left of first lay... Par chnicola on May 19, 19 1279 2 chnicola Total noobs experience with MK3S & question Par HC093HE on May 19, 19 2452 17 HC093HE First layer calibration error. First time user... Par Arcannys on May 18, 19 1453 1 Arcannys What is the expected i3 mk3S extruder motor te... Par GregB on May 18, 19 2567 13 GregB First build problem Par Cyranova on May 18, 19 1193 1 Cyranova First layer issue at some specific bed area Answered Par Vojtěch on May 17, 19 4969 22 Desti Failed XYZ Calibration Par 2002superhawk on May 17, 19 2189 13 2002superhawk Had to replace PTFE, now going backwards, prin... Par Nigel on May 17, 19 2819 11 redherring9 What material are the components? Par Vojtěch on May 16, 19 3956 5 john.c52 Extrusion slows and stops at a predictable poi... Par GregB on May 16, 19 2518 19 GregB Assembly X-axis smooth rod issue Par Vojtěch on May 16, 19 2059 3 brightwing Selftest print fan failure Par Shelby Teknolo... on May 15, 19 1711 3 Shelby Teknol... After installation, which program to use? Par -- on May 15, 19 1394 5 HoofedGibbon5... Had to replace hot end. Still not happy with p... Par -- on May 15, 19 1558 5 rachel.s5 Heavy printer problems because of under extrus... Par SiedlerK on May 14, 19 3862 11 SiedlerK Easy way to raise extruder out of the way afte... Par Chualzo on May 14, 19 9312 6 Chualzo error in the selftest: left fan Par Seb74 on May 14, 19 1510 3 carlos First Layer Cal one side higher than other Par TLowman92 on May 14, 19 2803 3 TLowman92 Page 159 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :