English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 151 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author First layer issues (and fix) Da bobstro on Jul 31, 19 14130 9 Laird Popkin What went wrong? Da mmihi on Jul 31, 19 2358 6 mmihi Mk3S IR Filament Sensor Da bernardjbisel on Jul 31, 19 4565 15 John~T Calibrate XYZ Fail i3 MK3 Da reesor on Jul 31, 19 3464 15 reesor Assembly guide Bondtech aligment, black nylon ... Da -- on Jul 30, 19 3251 4 Mistral33 MK3S Upgrade - Hotend loose Da Sunshadow on Jul 30, 19 2944 3 Sunshadow Extruder idler tensioner issue Da Mike01Hu on Jul 30, 19 4337 5 Mike01Hu Leftover red cable from hotend Da -- on Jul 30, 19 4202 19 prusanewuser MK3S - Hot Extruder and skipping at start time Da TigerClaw35 on Jul 30, 19 1774 1 TigerClaw35 New kit, can not calibrate. Da dispo on Jul 30, 19 2811 10 dispo Bad accuracy on x-axis Da -- on Jul 29, 19 3461 5 4Bob Octoprint stopped Da bobstro on Jul 29, 19 1786 2 luka.b3 Troubleshooting fine pillars Da lindharin on Jul 29, 19 6052 16 laurel.w Self test at hotend check does a reboot Da jkunjoonju on Jul 28, 19 2719 3 jkunjoonju Why does this happen at the same spot? Da -- on Jul 27, 19 2144 3 ametwalyhsgca Deteriorating nozzle temperature correctness l... Da bobstro on Jul 27, 19 2506 4 Cronostitan Calibration XYZ failed Da plevin on Jul 27, 19 5533 20 Laura Print problems Da luka.b3 on Jul 27, 19 1925 10 luka.b3 Weird Noise during print Da Elad6k on Jul 26, 19 4005 19 clementszwech... Filament stuck Da kronoss on Jul 26, 19 3954 9 kronoss Pagina 151 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Condividi: